P1441

DTC P1441 EVAP System Flow During Non-Purge (1 Of 2):

DTC P1441 EVAP System Flow During Non-Purge (2 Of 2):

EVAP System:

Circuit Description
The evaporative system includes the following components:

^ The fuel tank.
^ The Evaporation Emission (EVAP) vent solenoid.
^ The fuel tank pressure sensor.
^ The fuel pipes and hoses.
^ The vapor lines.
^ The fuel cap.
^ The evaporative emission canister.
^ The purge lines.
^ The EVAP purge solenoid.

The EVAP purge solenoid valve allows the manifold vacuum to purge the canister. The Vehicle Control Module (VCM) supplies a ground in order to energize the solenoid valve (purge ON). The EVAP purge solenoid control by the VCM is Pulse Width Modulated (PWM) or turned ON and OFF several times a second. The duty cycle (pulse width) is determined by the engine operating conditions including the load, the throttle position, the coolant temperature, and the ambient temperature. The duty cycle is calculated by the VCM, and the output is commanded when certain conditions have been met.

The system checks for conditions that cause the EVAP system to purge continuously by commanding the EVAP vent solenoid ON and the EVAP purge solenoid OFF (EVAP vent solenoid CLOSED, EVAP purge PWM 0%). If the fuel tank pressure level increases during the test, a continuous purge flow condition is indicated. The following items can cause this condition:

^ A leaking EVAP purge solenoid.
^ A grounded EVAP purge solenoid driver circuit If any of these conditions are present, a DTC P1441 sets. This DTC is a type B DTC.

Conditions For Setting The DTC
The Following Conditions will set the DTC:

1. No Manifold Absolute Pressure (MAP) sensor DTCs.
2. No Throttle Position (TP) sensor DTCs.
3. No Vehicle Speed Sensor (VSS) DTCs.
4. No HO2S DTCs.
5. No Engine Coolant Temperature (ECT) DTCs.
6. The DTC P0125 not active.
7. No Intake Air Temperature (IAT) sensor DTCs.
8. No Fuel Level DTCs.
9. The ECT is greater than 3.75°C (38.75°F) but less than 30°C (86°F).
10. The IAT is greater than 3.75°C (38.75°F) but less than 30°C (86°F).
11. Start up ECT is not more than 8.25°C (46.85°F) greater than the start up IAT.
12. Start up IAT is not more than 1.5°C (34.7°F) greater than the start up ECT.
13. The Fuel Level is greater than 10% and 85%.
14. The Baro is greater than 72.5 kPa.
15. The System Voltage is greater than 10 volts but less than 17 volts.
16. During the diagnostic test, the VCM detects a continuous open purge flow condition.

Action Taken When The DTC Sets

^ The VCM turns on the Malfunction Indicator Lamp (MIL) 2 consecutive failures.
^ The VCM records the operating conditions at the time the diagnostic fails. Freeze Frame and Failure Records stores this information.

Conditions For Clearing The MIL/DTC
The Following Conditions will clear the DTC:

^ The VCM turns the MIL off on the third consecutive trip cycle during which the diagnostic has been run and the fault condition is no longer present.
^ A history DTC clears after 40 consecutive warm-up cycles have occurred without a fault.
^ The scan tool Clear Info function or disconnecting the VCM battery teed can clear the DTC.

Diagnostic Aids
Check for the following conditions:

^ Inspect the EVAP lines for charcoal contamination if the EVAP Purge Solenoid was replaced. If charcoal contamination is present, replace the EVAP canister. Clean the EVAP purge line in order to remove any additional charcoal.
^ Inspect the VCM for poor connection. Inspect the harness connectors for the following items:

- Backed out terminals.
- Improper mating.
- Broken locks.
- Improperly formed or damaged terminals.
- Poor terminal to wiring connections.

^ Inspect the wiring harness for damage. If the harness looks OK, connect the Enhanced EVAP Pressure Purge Diagnostic Cart to the EVAP service port. Pressurize the EVAP system to 10 in. H2O. Observe the Fuel Tank Pressure display on the scan tool while moving connectors and wiring harnesses related to the EVAP purge solenoid. A sudden change in the display indicates the location of the fault.

Refer to Carbon Particle Removal from EVAP System before starting repairs. Service and Repair

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help to determine how often the condition that caused the DTC to set occurs. This may assist in diagnosing the condition.

Test Description
The numbers below refer to the step numbers on the diagnostic table.

2. This step checks the fuel tank pressure sensor at ambient pressure. The fuel tank pressure sensor is zeroed at every key on to compensate for changes in atmospheric pressure.
3. This step checks for a stuck open EVAP purge solenoid.
4. This step verifies that the fuel tank pressure sensor accurately reacts to EVAP system pressure changes.