Housing Assembly HVAC: Service and Repair

Heater/Vent Module Replacement

Removal Procedure






1. Remove the instrument panel. Refer to Instrument Panel Carrier Replacement Service and Repair.
2. Drain the engine coolant. Refer to Cooling System Draining and Filling Service and Repair.
3. On vehicles with automatic climate control only, cut (1) the outer layer of the A/C evaporator and blower module in order to access the service access cover. Refer to Blower Motor and Fan Replacement Service and Repair.
4. On vehicles with automatic climate control only, remove the service access cover mounting screws.
5. On vehicles with automatic climate control only, remove the service access cover.
6. On vehicles without automatic climate control, remove the blower motor resistor. Refer to Blower Motor Resistor Replacement Service and Repair.

Important: Mark and use the same mounting bolt (located behind the A/C evaporator and blower module) for the heater assembly during the installation process. Other mounting bolts are longer and will obstruct the operation of the temperature door.

7. Remove the heat/vent module mounting bolt through the blower motor resistor or service access cover opening.






8. On vehicles with A/C only, remove the right wheel house panel. Refer to Wheelhouse Panel Replacement Service and Repair.
9. On vehicles with A/C only, raise and support vehicle.
10. On vehicles with A/C only, remove the front right tire.
11. On the Utility only, remove the A/C evaporator and blower module heat shield screws.
12. On the Utility only, slide the A/C evaporator and blower module heat shield toward the front of the vehicle.
13. Remove the 2 lower heat/vent module mounting nuts.
14. On the Utility only, remove the A/C evaporator and blower module heat shield bracket.
15. Remove the bottom right heat/vent module mounting bolt from inside the vehicle.

Important: The heat/vent mounting stud has a flange on the inside and cannot be removed from under the hood. Stop turning the stud after the threads are off the heat/vent module.

16. On the Utility only, while an assistant inside the vehicle pulls the bottom right corner of the heat/vent module approximately 1 inch back, remove the 2 heat/vent module mounting studs.
17. On vehicles with A/C only, lower the vehicle.






18. On vehicles with a 2.2L engine only, remove the engine wiring harness bracket located at the rear of the intake manifold. Refer to Valve Rocker Arm Cover Replacement Service and Repair.
19. Remove the heat/vent module mounting bolt located at the lower left side of the heater core to heater hose connection.
20. Remove the heat/vent module mounting nut located at the lower right side of the heater core to heater connection.

Important: The heat/vent mounting stud has a flange on the inside and cannot be removed from under the hood. Stop turning the stud after the threads are off the heat/vent module.

21. On the Utility only, loosen the heat/vent module mounting studs until the threads are free from the heat/vent module.
22. Disconnect all of the electrical connectors from the heat/vent module.
23. Disconnect all of the vacuum lines from the heater assembly.
24. Disconnect the heater hoses from the heater core.
25. Remove the heat/vent module from the vehicle.

Installation Procedure






1. If replacing the heat/vent module, transfer the components from the old heat/vent module as necessary.

Important: Before installing the heat/vent module to the vehicle, ensure that the heat/vent module mounting studs are located in the proper positions.

2. Install the heat/vent module to the vehicle.
3. Connect the heater hoses to the heater core.
4. Connect all of the vacuum lines to the heater assembly.
5. Connect all of the electrical connectors to the heat/vent module.
6. Install the bottom right heat/vent module mounting bolt from inside the vehicle approximately halfway into the threads.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

7. On the Utility only, install the heat/vent module mounting stud located at the lower right side of the heater core to heater hoses connection in the engine compartment.

Tighten
Tighten the heat/vent module mounting stud to 4.5 Nm (22 lb in).

8. On vehicles with A/C only, raise the vehicle.
9. On the Utility only, install the bottom right heat/vent mounting studs. Ask an assistant to pull the bottom right corner of the heat/vent module back from inside the vehicle.

Tighten
Tighten the heat/vent module mounting studs to 4.5 Nm (22 lb in).

10. On the Utility only, install the A/C evaporator and blower module heat shield bracket.
11. Install the heater/vent module mounting nuts.

Tighten
Tighten the heat/vent module mounting nuts to 4.5 Nm (22 lb in).

12. On the Utility only, slide the A/C evaporator and blower module heat shield into the original position.
13. On the Utility only, install the A/C evaporator and blower module heat shield screws.

Tighten
Tighten the A/C evaporator and blower module heat shield screws 2.2 Nm (19 lb in).






14. On vehicles with A/C only, install the right front tire.
15. On vehicles with A/C only, lower the vehicle.
16. Install the bottom right heat/vent module mounting bolt from inside the vehicle.

Tighten
Tighten the heat/vent module mounting bolt to 4.5 Nm (22 lb in).

17. On vehicles with A/C only, install the right wheel house panel. Refer to Wheelhouse Panel Replacement Service and Repair.






18. Install the heat/vent module mounting nut located at the lower right side of the heater core to heater connection.

Tighten
Tighten the heat/vent module mounting nut to 4.5 Nm (22 lb in).

19. Install the heat/vent module mounting bolt located at the lower left side of the heater core to heater hose connection.

Tighten
Tighten the heat/vent module mounting bolt to 4.5 Nm (22 lb in).

20. On vehicles with the 2.2L engine only, install the engine wiring harness bracket located at the rear of the intake manifold. Refer to Valve Rocker Arm Cover Replacement Service and Repair.






Important: Mark and use the same mounting bolt (located behind the A/C evaporator and blower module) for the heater assembly during the installation process. Other mounting bolts are longer and will obstruct the operation of the temperature door.

21. Install the heat/vent module mounting bolt through the blower motor resistor or service access cover opening.

Tighten
Tighten the heat/vent module mounting bolt to 4.5 Nm (22 lb in).

22. On vehicles without automatic climate control, install the blower motor resistor. Refer to Blower Motor Resistor Replacement Service and Repair.
22. On vehicles with automatic climate control only, install the service access cover.
23. On vehicles with automatic climate control only, install the service access cover mounting screws.
24. On vehicles with automatic climate control only, install the outer layer of the A/C evaporator and blower module. Refer to Blower Motor and Fan Replacement Service and Repair.
25. Refill the engine coolant. Refer to Cooling System Draining and Filling Service and Repair.
26. Install the instrument panel. Refer to Instrument Panel Carrier Replacement Service and Repair.