Pinpoint Test S: The SYNC System Audible Prompts Are Inoperative/Do Not Operate Correctly
Information and Entertainment System
Pinpoint Tests
Pinpoint Test S: The SYNC System Audible Prompts Are Inoperative/Do Not Operate Correctly
Refer to Wiring Diagram Set 130, Audio System for schematic and connector information. Diagrams By Number
Normal Operation
The Text-To-Speech (TTS) and voice prompt features speak certain text information and interaction requests in order to minimize driver distraction while driving. The ringtone alerts the driver to an incoming call.
Audible prompts can range from a simple tone to more elaborate spoken text, based on the customer setting. When interaction mode is set to standard, detailed guidance is provided. When interaction mode is set to advanced, most prompts are tones only and minimal audible guidance is provided. Refer to the Owner's Literature for further information on voice interaction.
The audio signals for the TTS and voice prompt features, the ringtones, and audio from an outside device during a phone call, are sent from the Accessory Protocol Interface Module (APIM) to the Audio Control Module (ACM).
This pinpoint test is intended to diagnose the following:
- Customer setting
- Wiring, terminals or connectors
- ACM
- APIM
PINPOINT TEST S: THE SYNC SYSTEM AUDIBLE PROMPTS ARE INOPERATIVE/DO NOT OPERATE CORRECTLY
NOTICE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
-------------------------------------------------
S1 CHECK THE AUDIBLE PROMPT SETTING
- Operate the audio system in SYNC mode.
- Verify the audible prompts are enabled. Refer to "SYNC Voice Recognition Feature" in the Owner's Literature.
- Press the VOICE button on the steering wheel controls and observe the SYNC audible prompt.
- Does the SYNC system produce an audible prompt correctly?
Yes
The system is operating correctly at this time. The concern was caused by a customer setting. INSTRUCT the customer in the correct operation of the audible prompt feature.
No
GO to S2.
-------------------------------------------------
S2 CHECK FOR A VOLTAGE SIGNAL FROM THE APIM
NOTICE: This pinpoint test step directs testing circuits using a back-probe method. Use the special back-probe tool specified in the tool list. Do not force test leads or other probes into connectors. Adequate care must be exercised to avoid connector terminal damage while ensuring that good electrical contact is made with the circuit or terminal. Failure to follow these instructions may cause damage to wiring, terminals, or connectors and subsequent electrical faults.
- Operate the audio system in SYNC mode.
- While pressing the VOICE button repeatedly, measure the AC voltage by backprobing between the ACM C240b-4, circuit VMN14 (WH/VT), harness side and the ACM C240b-5, circuit RMN14 (GY/BN), harness side.
- Is an AC voltage produced each time the VOICE switch is pressed?
Yes
GO to S6.
No
GO to S3.
-------------------------------------------------
S3 CHECK THE AUDIBLE PROMPT CIRCUITS FOR A SHORT TO VOLTAGE
- Ignition OFF.
- Disconnect: ACM C240b.
- Disconnect: APIM C2298.
- Ignition ON.
- Measure the voltage between the APIM C2298-3, circuit VMN14 (WH/VT), harness side and ground; and between the APIM C2298-4, circuit RMN14 (GY/BN), harness side and ground.
- Is any voltage present?
Yes
REPAIR the circuit in question. TEST the system for normal operation.
No
GO to S4.
-------------------------------------------------
S4 CHECK THE AUDIBLE PROMPT CIRCUITS FOR AN OPEN OR SHORT TO GROUND
- Ignition OFF.
- Measure the resistance between the APIM C2293-3, circuit VMN14 (WH/VT), harness side and the C240b-4, circuit VMN14 (WH/VT); and between the APIM C2293-3, circuit VMN14 (WH/VT), harness side and ground.
- Measure the resistance between the APIM C2293-4, circuit RMN14 (GY/BN), harness side and the C240b-5, circuit RMN14 (GY/BN); and between the APIM C2293-4, circuit RMN14 (GY/BN), harness side and ground.
- Are the resistances less than 5 ohms between the APIM and the ACM, and greater than 10,000 ohms between the APIM and ground?
Yes
GO to S5.
No
REPAIR the circuit in question. TEST the system for normal operation.
-------------------------------------------------
S5 CHECK FOR CORRECT APIM OPERATION
- Ignition OFF.
- Connect: ACM C240b.
- Disconnect the APIM connector.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect the APIM connector and make sure it seats correctly.
- Wait 2 minutes for the APIM to re-initialize.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new APIM. REFER to Accessory Protocol Interface Module (APIM) Accessory Protocol Interface Module (APIM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------
S6 CHECK FOR CORRECT ACM OPERATION
- Ignition OFF.
- Disconnect all the ACM connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the ACM connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new ACM. REFER to Audio Control Module (ACM) Audio Control Module (ACM). TEST the system for normal operation.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
-------------------------------------------------