P0982
DTC P0982: Short in Shift Solenoid Valve D CircuitNOTE:
^ Before you troubleshoot, record all freeze data and any on-board snapshot with the HDS, and review General Troubleshooting Information.
^ This code is caused by an electrical circuit problem and cannot be caused by a mechanical problem in the transmission.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine with the shift lever in P, and wait for at least 1 second.
4. Check for DTCs with the HDS.
Is DTC P0982 indicated?
YES - Go to step 8.
NO - Go to step 5.
5. Select Shift Solenoid Valve D in the Miscellaneous Test Menu, and test shift solenoid valve D with the HDS.
Is a clicking sound heard?
YES - Go to step 6.
NO - Go to step 8.
6. Start the engine with the shift lever in P, and wait for at least 1 second.
7. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate FAILED?
YES - Go to step 8.
NO - If the HDS indicates PASSED, intermittent failure, the system is OK at this time. Check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM. If the HDS indicates NOT COMPLETED, go to step 5.
8. Turn the ignition switch to LOCK (0).
9. Jump the SCS line with the HDS.
10. Disconnect PCM connectors B (44P) and C (44P).
11. Measure the resistance between PCM connector terminals B11 and C40.
Is there less than 12 ohms?
YES - Go to step 12.
NO - Go to step 21.
12. Disconnect the shift solenoid harness connector.
13. Check for continuity between PCM connector terminals B11 and C40.
Is there continuity?
YES - Repair short to body ground in the wire between PCM connector terminal 1311 and the shift solenoid harness connector, then go to step 15.
NO - Go to step 14.
14. Inspect shift solenoid valve D and the shift solenoid harness.
Is shift solenoid valve D and the harness OK?
YES - Go to step 21.
NO - Replace shift solenoid valve D or the shift solenoid harness, then go to step 15.
15. Reconnect all connectors.
16. Turn the ignition switch to ON (II).
17. Clear the DTC with the HDS.
18. Start the engine with the shift lever in P, and wait for at least 1 second.
19. Check for DTCs with the HDS.
Is DTC P0982 indicated?
YES - Check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM, then go to step 1.
NO - Go to step 20.
20. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES - Troubleshooting is complete. If any other DTCs were indicated in step 19, go to the indicated DTC's troubleshooting.
NO - If the HDS indicates FAILED, check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM, then go to step 1. If the HDS indicates NOT COMPLETED, go to step 18.
21. Update the PCM if it does not have the latest software, or substitute a known good PCM.
22. Start the engine with the shift lever in P, and wait for at least 1 second.
23. Check for DTCs with the HDS.
Is DTC P0982 indicated?
YES - Check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM. If the PCM was updated, substitute a known good PCM, then go to step 22. If the PCM was substituted, go to step 1.
NO - Go to step 24.
24. Monitor the OBD STATUS for P0982 in the DTCs MENU with the HDS.
Does the HDS indicate PASSED?
YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM. If any other DTCs were indicated in step 23, go to the indicated DTC's troubleshooting.
NO - If the HDS indicates FAILED, check for intermittent short to body ground in the wire between shift solenoid valve D and the PCM. If the PCM was updated, substitute a known-good PCM, then go to step 22. If the PCM was substituted, go to step 1. If the HDS indicates NOT COMPLETED, go to step 22.