Operation CHARM: Car repair manuals for everyone.
Home >> Infiniti Truck >> 2011 >> EX35 AWD V6-3.5L (VQ35HR) >> Repair and Diagnosis >> Instrument Panel, Gauges and Warning Indicators >> Dashboard / Instrument Panel >> Service and Repair >> Removal And Installation

Removal And Installation





INSTRUMENT PANEL ASSEMBLY


Removal and Installation


WORK STEP
When removing instrument panel assembly, combination meter, AV control unit, and center console assembly take steps in the order shown by the number below.






WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more.

CAUTION:
When removing, always use a remover tool that is made of plastic.

REMOVAL
1. Remove console finisher assembly.
1. Put selector lever in drive position.
2. Remove selector lever knob. Removal And Installation.





3. Pull console finisher (1), upward to disengage from center console.
4. Disconnect harness connectors.

Triangle: Pawl
Square: Metal Clip





2. Disconnect console sub harness connectors (A).
3. Remove center console assembly fixing screws (B).





4. Remove console center finisher.
1. Open the console lid assembly.
2. Remove console pocket.
3. Pull upward to release console center finisher fixing pawls from center console assembly.
4. Disconnect harness connectors.

Triangle: Pawl






5. Remove console rear finisher.
1. Put front seat to frontmost position.
2. Pull back the console rear finisher (1) with remover tool (A).
3. Disconnect inside key antenna connector.

Square: Metal Clip






6. Remove rear ventilator duct 2 (1). Rear Ventilator Duct 1 Rear Ventilator Duct 2 Foot Grille, "REAR
VENTILATOR DUCT 2 : Removal and Installation".
7. Remove center console assembly fixing screws (A).
8. Remove center console assembly.
1. Put front seat to rearmost position.
2. Lift up center console assembly back side.





9. Remove instrument side finisher LH.
1. Insert a remover tool into lower space.
2. Pull the instrument side finisher LH (1) crosswise.

Circle: Clip
Triangle: Pawl





10. Remove instrument lower panel LH.
1. Remove hood opener lever fixing bolts (A).
2. Pull back instrument lower panel LH (1).
3. Remove skirt clips of steering column lower cover (2).
4. Release data link connector (pawl) then remove it from instrument lower panel LH.
5. Disconnect harness connectors and aspirator duct.

Circle: Clip
Triangle: Pawl
Square: Metal Clip

11. Remove driver air bag module. Removal And Installation.
12. Remove steering wheel. Removal And Installation.
13. Remove steering column covers.
1. Remove steering column mask (1).
2. Remove steering column cover fixing screws (A).
3. Pull up steering column upper cover (2).
4. Remove cluster lid A (4) fixing clips and pawls, and then remove steering column upper cover.
5. Pull down steering column lower cover (3), and then remove steering column lower cover.
6. Disconnect ADP steering switch connector. (with ADP)

Circle: Clip
Triangle: Pawl





14. Remove combination switch. Removal And Installation.
15. Remove spiral cable. Removal And Installation.





16. Remove cluster lid A (upper).
1. Pull back cluster lid A (upper) (1), and disengage pawls and metal clips.
2. Remove cluster lid A (upper).

Triangle: Pawl
Square: Metal Clip





17. Remove cluster lid A.
1. Remove cluster lid A (1) fixing screws (A).
2. Pull back cluster lid A, and disengage metal clips.
3. Remove cluster lid A.

Square: Metal Clip

18. Remove combination meter. Exploded View.





19. Remove instrument harness (1) fixing clips (A).





20. Disconnect trip A/B reset switch (1) harness connector (A). Exploded View.
21. Remove front body side welt LH. Removal And Installation.
22. Remove front pillar garnish LH. Removal And Installation.





23. Disconnect antenna connectors (A).
24. Remove harness clip (B).





25. Remove speaker grille LH.
1. Pull up and back speaker grille LH (1).
2. Disconnect front squawker harness connector.

Circle: Clip
Triangle: Pawl





26. Remove center speaker grille.
1. Disengage center speaker grille (1) fixing clips and pawls with remover tool (A).
2. Pull up center speaker grille.

Circle: Clip
Triangle: Pawl

27. Remove center speaker (with BOSE AUDIO). Removal And Installation Bose Audio Without Navigation.





28. Remove instrument side panel LH.
1. Remove instrument side panel LH (1) fixing screws (A).
2. Pull toward the arrow direction.

Circle: Clip

29. Remove inside key antenna. Removal And Installation Intelligent Key System.





30. Remove harness connector bracket (1) fixing screw (A).





31. Remove cluster lid C.
1. Remove cluster lid C (1) fixing screws (A).
2. Pull down and back cluster lid C.
3. Disconnect harness connectors.

Triangle: Pawl






32. Remove cluster lid D.
1. Remove cluster lid D (1) fixing screws (A).
2. Pull back cluster lid D.
3. Disconnect harness connectors.

Triangle: Pawl

33. Remove display unit. Removal And Installation Base Audio Without Navigation.
34. Remove AV control unit. Removal And Installation Base Audio Without Navigation.
35. Remove push button ignition switch. Removal And Installation Intelligent Key System.
36. Remove front defroster grille LH. Front Defroster Grille.
37. Remove front defroster grille RH. Front Defroster Grille.





38. Remove instrument side finisher RH.
1. Insert a remover tool into lower space.
2. Pull the instrument side finisher RH (1) crosswise.

Circle: Clip
Triangle: Pawl

39. Remove glove box assembly.
1. Open the glove box.





2. Pull back glove box assembly (1).





3. Remove damper pin (1) of left side.

Circle: Clip






40. Remove instrument lower cover.
1. Pull downward, disengaged pawls.
2. Pull back instrument lower cover (1).
3. Disconnect illumination lamp harness connector.

Triangle: Pawl






41. Remove instrument lower panel RH.
1. Remove instrument lower panel RH (1) fixing screws (A).
2. Pull back instrument lower panel RH.
3. Disconnect glove box lamp harness connector.

Triangle: Pawl

42. Disconnect front passenger air bag module connector. Exploded View.
43. Remove front passenger air bag module fixing bolt. Removal And Installation.





44. Remove instrument side panel RH.
1. Remove instrument side panel RH (1) fixing screws (A).
2. Pull toward the arrow direction.

Circle: Clip

45. Remove front body side welt RH. Removal And Installation.
46. Remove front pillar garnish RH. Removal And Installation.





47. Remove speaker grille RH.
1. Pull up and back tweeter grille RH (1).
2. Disconnect front squawker harness connector.

Circle: Clip
Triangle: Pawl

48. Remove instrument panel assembly.
1. Remove instrument panel assembly mounting bolts (A), screws (B) and clips (C).






CAUTION:
Cover tool with a shop cloth to prevent windshield glass being damaged.
2. Remove instrument panel from passenger door opening portion.

CAUTION:
- Cover center console upper surface with a shop cloth to prevent it from being damaged.
- When removing instrument panel assembly, 2 workers are required so as to prevent it from dropping.
49. Remove the following parts after removing instrument panel assembly.
- Front passenger air bag module: Removal And Installation.
- Center ventilator grille LH/RH: Center Ventilator Grille.
- Side ventilator grille LH/RH: Side Ventilator Grille.
- Ventilator duct LH/RH: Ventilator Duct.
- Adaptor duct: Adaptor Duct.
- Defroster nozzle: Defroster Nozzle.
- Side defroster nozzle LH/RH: Side Defroster Nozzle.
- Antenna feeder: Base Audio Without Navigation.
- GPS antenna: Exploded View Bose Audio With Navigation.
- Trip A/B reset switch: Removal And Installation.

INSTALLATION
Note the following items, and then install in the reverse order of removal.

CAUTION:
- Never use the steering wheel mounting nut after removal, replace with the new nut.
- Never use the driver air bag module mounting bolts after removal, replace with the new bolts.
- Never use the passenger air bag module mounting bolt after removal, replace with the new bolt.
pro multis · About Operation CHARM