Removal and Installation
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
WORK STEP
When removing instrument panel assembly, combination meter, AV control unit, and center console assembly take steps in the order shown by the number below.
WARNING:
Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes or more.
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.Remove console finisher assembly.
1.Put selector lever in drive position.
2.Remove selector lever knob. Refer to "Removal and Installation" Removal and Installation.
3.Pull console finisher (1), upward to disengage from center console.
4.Disconnect harness connectors.
2.Disconnect console sub harness connectors (A).
3.Remove center console assembly fixing screws (B).
4.Remove console center finisher.
1.Open the console lid assembly.
2.Remove console pocket.
3.Pull upward to release console center finisher fixing pawls from center console assembly.
4.Disconnect harness connectors.
5.Remove console rear finisher.
1.Put front seat to front most position.
2.Pull back the console rear finisher (1) with remover tool (A).
3.Disconnect inside key antenna connector.
6.Remove rear ventilator duct 2 (1). Refer to "REAR VENTILATOR DUCT 2 : Removal and Installation" Rear Ventilator Duct 2.
7.Remove center console assembly fixing screws (A).
8.Remove center console assembly.
1.Put front seat to rear most position.
2.Lift up center console assembly back side.
9.Remove instrument side finisher LH.
1.Insert a remover tool into lower space.
2.Pull the instrument side finisher LH (1) crosswise.
10.Remove instrument lower panel LH.
1.Remove hood opener lever fixing bolts (A).
2.Pull back instrument lower panel LH (1).
3.Remove skirt clips of steering column lower cover (2).
4.Release data link connector (pawl) then remove it from instrument lower panel LH.
5.Disconnect harness connectors and aspirator duct.
11.Remove driver air bag module. Refer to "Removal and Installation" Removal and Installation.
12.Remove steering wheel. Refer to "Removal and Installation" Removal and Installation.
13.Remove steering column covers.
1.Remove steering column mask (1).
2.Remove steering column cover fixing screws (A).
3.Pull up steering column upper cover (2).
4.Remove cluster lid A (4) fixing clips and pawls, and then remove steering column upper cover.
5.Pull down steering column lower cover (3), and then remove steering column lower cover.
6.Disconnect ADP steering switch connector. (with ADP)
14.Remove combination switch. Refer to "Removal and Installation" Removal and Installation.
15.Remove spiral cable. Refer to "Removal and Installation" Removal and Installation.
16.Remove cluster lid A (upper).
1.Pull back cluster lid A (upper) (1), and disengage pawls and metal clips.
2.Remove cluster lid A (upper).
17.Remove cluster lid A.
1.Remove cluster lid A (1) fixing screws (A).
2.Pull back cluster lid A, and disengage metal clips.
3.Remove cluster lid A.
18.Remove combination meter. Refer to "Exploded View" Exploded View.
19.Remove instrument harness (1) fixing clips (A).
20.Disconnect trip A/B reset switch (1) harness connector (A).
Refer to "Exploded View" Exploded View.
21.Remove front body side welt LH. Refer to "Removal and Installation" Removal and Installation.
22.Remove front pillar garnish LH. Refer to "Removal and Installation" Removal and Installation.
23.Disconnect antenna connectors (A).
24.Remove harness clip (B).
25.Remove speaker grille LH.
1.Pull up and back speaker grille LH (1).
2.Disconnect front squawker harness connector.
26.Remove center speaker grille.
1.Disengage center speaker grille (1) fixing clips and pawls with remover tool (A).
2.Pull up center speaker grille.
27.Remove center speaker (with BOSE AUDIO). Refer to "Removal and Installation" Without Navigation.
28.Remove instrument side panel LH.
1.Remove instrument side panel LH (1) fixing screws (A).
2.Pull toward the arrow direction.
29.Remove inside key antenna. Refer to "INSTRUMENT CENTER : Removal and Installation" Removal and Installation.
30.Remove harness connector bracket (1) fixing screw (A).
31.Remove cluster lid C.
1.Remove cluster lid C (1) fixing screws (A).
2.Pull down and back cluster lid C.
3.Disconnect harness connectors.
32.Remove cluster lid D.
1.Remove cluster lid D (1) fixing screws (A).
2.Pull back cluster lid D.
3.Disconnect harness connectors.
33.Remove display unit. Refer to "Removal and Installation" Base Audio.
34.Remove AV control unit. Refer to "Removal and Installation" Base Audio.
35.Remove push button ignition switch. Refer to "Removal and Installation" Push-Button Ignition Switch.
36.Remove front defroster grille LH. Refer to "FRONT DEFROSTER GRILLE : Removal and Installation" Front Defroster Grille.
37.Remove front defroster grille RH. Refer to "FRONT DEFROSTER GRILLE : Removal and Installation" Front Defroster Grille.
38.Remove instrument side finisher RH.
1.Insert a remover tool into lower space.
2.Pull the instrument side finisher RH (1) crosswise.
39.Remove glove box assembly.
1.Open the glove box.
2.Pull back glove box assembly (1).
3.Remove damper pin (1) of left side.
40.Remove instrument lower cover.
1.Pull downward, disengaged pawls.
2.Pull back instrument lower cover (1).
3.Disconnect illumination lamp harness connector.
41.Remove instrument lower panel RH.
1.Remove instrument lower panel RH (1) fixing screws (A).
2.Pull back instrument lower panel RH.
3.Disconnect glove box lamp harness connector.
42.Disconnect passenger air bag module connector. Refer to "Exploded View" Exploded View.
43.Remove passenger air bag module fixing bolt. Refer to "Removal and Installation" Removal and Installation.
44.Remove instrument side panel RH.
1.Remove instrument side panel RH (1) fixing screws (A).
2.Pull toward the arrow direction.
45.Remove front body side welt RH. Refer to "Removal and Installation" Removal and Installation.
46.Remove front pillar garnish RH. Refer to "Removal and Installation" Removal and Installation.
47.Remove speaker grille RH.
1.Pull up and back tweeter grille RH (1).
2.Disconnect front squawker harness connector.
48.Remove instrument panel assembly.
1.Remove instrument panel assembly mounting bolts (A), screws (B) and clips (C).
CAUTION:
Cover tool with a shop cloth to prevent windshield glass being damaged.
2.Remove instrument panel from passenger door opening portion.
CAUTION:
- Cover center console upper surface with a shop cloth to prevent it from being damaged.
- When removing instrument panel assembly, 2 workers are required so as to prevent it from dropping.
49.Remove the following parts after removing instrument panel assembly.
- Passenger air bag module: Refer to "Removal and Installation" Removal and Installation.
- Center ventilator grille LH/RH: Refer to "CENTER VENTILATOR GRILLE : Removal and Installation" Center Ventilator Grille.
- Side ventilator grille LH/RH: Refer to "SIDE VENTILATOR GRILLE : Removal and Installation" Side Ventilator Grille.
- Ventilator duct LH/RH: Refer to "VENTILATOR DUCT : Removal and Installation" Ventilator Duct.
- Adaptor duct: Refer to "ADAPTOR DUCT : Removal and Installation" Adaptor Duct.
- Defroster nozzle: Refer to "DEFROSTER NOZZLE : Removal and Installation" Defroster Nozzle.
- Side defroster nozzle LH/RH: Refer to "SIDE DEFROSTER NOZZLE : Removal and Installation" Side Defroster Nozzle.
- Antenna feeder: Refer to "Feeder Layout" Base Audio.
- GPS antenna: Refer to "Exploded View" Exploded View.
- Trip A/B reset switch: Refer to "Removal and Installation" Removal and Installation.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
- Never use the steering wheel mounting nut after removal, replace with the new nut.
- Never use the driver air bag module mounting bolts after removal, replace with the new bolts.
- Never use the passenger air bag module mounting bolt after removal, replace with the new bolt.