Vehicle Does Not Creep Backward In "R" Position

Vehicle Does Not Creep Backward in "R" Position

SYMPTOM: The vehicle does not creep in "R" position. Or an extreme lack of acceleration is observed.

DIAGNOSTIC PROCEDURE

1.CHECK SELF-DIAGNOSTIC RESULTS

With CONSULT-III
^ Select "SELF-DIAG RESULTS" mode for "TRANSMISSION" with CONSULT-III.

Without CONSULT-III
^ Perform the self-diagnosis. Refer to AT-92, "Diagnosis Procedure without CONSULT-III". Diagnosis Procedure Without Consult-III

Is any malfunction detected by self-diagnosis results?
YES >> Check malfunctioning system. Refer to AT-85, "CONSULT-III Function (TRANSMISSION)", AT-92, "Diagnosis Procedure without CONSULT-III".
Consult-III Function (Transmission)
Diagnosis Procedure Without Consult-III
NO >> GO TO 2.

2.CHECK A/T POSITION
Check A/T position.
OK or NG
OK >> GO TO 3.
NG >> Adjust A/T position. Refer to AT-202, "Adjustment of A/T Position". Adjustments

3.CHECK A/T FLUID LEVEL
Check A/T fluid level.
OK or NG
OK >> GO TO 4.
NG >> Refill [1][2]ATF.

4.CHECK STALL TEST
Check stall revolution with selector lever in "M" and "R" positions. Refer to AT-50, "Inspections Before Trouble Diagnosis". Inspections Before Trouble Diagnosis
OK or NG
OK >> GO TO 6.
OK in "M" position, NG in "R" position >> GO TO 5
NG in both "M" and "R" positions >> GO TO 8.

5.DETECT MALFUNCTIONING ITEM
1. Disassemble A/T.
2. Check the following.
- Reverse brake.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

6.CHECK LINE PRESSURE
Check line pressure with the engine idling. Refer to AT-50, "Inspections Before Trouble Diagnosis". Inspections Before Trouble Diagnosis
OK or NG
OK >> GO TO 9.
NG - 1 >> Line pressure high: GO TO 7.
NG - 2 >> Line pressure low: GO TO 8.

7.DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM.
2. Disassemble A/T.
3. Check the following.
- Oil pump assembly.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

8.DETECT MALFUNCTIONING ITEM
1. Check control valve with TCM.
2. Disassemble A/T.
3. Check the following.
- Oil pump assembly.
- Power train system.
- Transmission case.
OK or NG
OK >> GO TO 9.
NG >> Repair or replace damaged parts.

9.CHECK A/T FLUID CONDITION
1. Remove oil pan.
2. Check A/T fluid condition. Refer to AT-44, "How to Perform Trouble Diagnosis for Quick and Accurate Repair". How to Perform Trouble Diagnosis For Quick and Accurate Repair
OK or NG
OK >> GO TO 10.
NG >> GO TO 13.

10.DETECT MALFUNCTIONING ITEM
Check malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-61, "Symptom Chart" (Symptom No.43). Symptom Table
OK or NG
OK >> GO TO 11.
NG >> Repair or replace damaged parts.

11.CHECK SYMPTOM
Check again. Refer to "CHECK AT IDLE".
OK or NG
OK >> INSPECTION END
NG >> GO TO 12.

12.CHECK TCM
1. Check TCM input/output signals. Refer to AT-84, "TCM Input/Output Signal Reference Value". Pinout Values and Diagnostic Parameters
2. If NG, recheck A/T assembly harness connector terminals for damage or loose connection with harness connector.
OK or NG
OK >> INSPECTION END
NG >> Repair or replace damaged parts.

13.DETECT MALFUNCTIONING ITEM
Check malfunction items. If any items are damaged, repair or replace damaged parts. Refer to AT-61, "Symptom Chart" (Symptom No.43). Symptom Table
OK or NG
OK >> GO TO 11.
NG >> Repair or replace damaged parts.