P0133
P0133, P0153 A/F SENSOR 1
DTC Logic
DTC DETECTION LOGIC
To judge the malfunction of A/F sensor 1, this diagnosis measures response time of the A/F signal computed by ECM from the A/F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel feedback control constant, and the A/F sensor 1 temperature index. Judgment is based on whether the compensated time (the A/F signal cycling time index) is inordinately long or not.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
Will CONSULT-III be used?
YES - GO TO 2.
NO - GO TO 5.
2.PERFORM DTC CONFIRMATION PROCEDURE-I
WITH CONSULT-III
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Turn ignition switch ON.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Restart engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
6. Let engine idle for 1 minute.
7. Select "A/F SEN1(B1) P1278/P1279" (for DTC P0133) or "A/F SEN1(B2) P1288/P1289" (for DTC P0153) of "A/F SEN1" in "DTC WORK SUPPORT" mode with CONSULT-III.
8. Touch "START".
Is "COMPLETED" displayed on CONSULT-III screen?
YES - GO TO 3
NO - GO TO 4.
3.PERFORM DTC CONFIRMATION PROCEDURE-II
Touch "SELF-DIAG RESULT".
Which is displayed on CONSULT-III screen?
OK - INSPECTION END
NG - Proceed to SEE Diagnosis Procedure.
4.PERFORM DTC CONFIRMATION PROCEDURE-II
1. After perform the following procedure, "TESTING" will be displayed on the CONSULT-III screen.
- Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
- Fully release accelerator pedal and then let engine idle for approximately 10 seconds.
If "TESTING" is not displayed after 10 seconds, Specification Value.
2. Wait for approximately 20 seconds at idle under the condition that "TESTING" is displayed on the CONSULT-III screen.
3. Check that "TESTING" changes to "COMPLETED".
If "TESTING" changed to "OUT OF CONDITION", Specification Value.
4. Touch "SELF-DIAG RESULT".
Which is displayed on CONSULT-III screen?
OK - INSPECTION END
NG - Proceed to SEE Diagnosis Procedure.
5.CHECK AIR-FUEL RATIO SELF-LEARNING VALUE
WITH GST
1. Start engine and warm it up to normal operating temperature.
2. Select Service $01 with GST.
3. Calculate the total value of "Short term fuel trim" and "Long term fuel trim" indications.
Is the total percentage within �15%?
YES - GO TO 7.
NO - GO TO 6.
6.DETECT MALFUNCTIONING PART
Check the following.
- Intake air leaks
- Exhaust gas leaks
- Incorrect fuel pressure
- Lack of fuel
- Fuel injector
- Incorrect PCV hose connection
- PCV valve
- Mass air flow sensor
- Repair or replace malfunctioning part.
7.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least 1 minute under no load.
3. Let engine idle for 1 minute.
4. Increase the engine speed up to between 4,000 and 5,000 rpm and maintain that speed for 10 seconds.
5. Fully release accelerator pedal and then let engine idle for approximately 1 minute.
6. Check 1st trip DTC.
Is 1st trip DTC detected?
YES - Proceed to SEE Diagnosis Procedure.
NO - INSPECTION END
Diagnosis Procedure
1.RETIGHTEN AIR FUEL RATIO SENSOR 1
Loosen and retighten the air fuel ratio (A/F) sensor 1. Exploded View.
- GO TO 2.
2.CHECK EXHAUST GAS LEAKAGE
1. Start engine and run it at idle.
2. Listen for an exhaust gas leakage before three way catalyst (manifold).
Is exhaust gas leakage detected?
YES - Repair or replace malfunctioning part.
NO - GO TO 3.
3.CHECK FOR INTAKE AIR LEAKAGE
Listen for an intake air leakage after the mass air flow sensor.
Is intake air leakage detected?
YES - Repair or replace malfunctioning part.
NO - GO TO 4.
4.CLEAR THE MIXTURE RATIO SELF-LEARNING VALUE
1. Clear the mixture ratio self-learning value. Work Procedure.
2. Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171, P172, P0174 or P0175 detected? Is it difficult to start engine?
YES - Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. P0171 or P0172.
NO - GO TO 5.
5.CHECK AIR FUEL RATIO SENSOR 1 POWER SUPPLY CIRCUIT
1. Disconnect air fuel ratio (A/F) sensor 1 harness connector.
2. Turn ignition switch ON.
3. Check the voltage between A/F sensor 1 harness connector and ground.
Is the inspection result normal?
YES - GO TO 6.
NO - Repair open circuit, short to ground or short to power in harness or connectors.
6.CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.
5. Also check harness for short to power.
Is the inspection result normal?
YES - GO TO 7.
NO - Repair open circuit, short to ground or short to power in harness or connectors.
7.CHECK A/F SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.
4. Also check harness for short to power.
Is the inspection result normal?
YES - GO TO 8.
NO - Repair open circuit, short to ground or short to power in harness or connectors.
8.CHECK A/F SENSOR 1 HEATER
P0031.
Is the inspection result normal?
YES - GO TO 9.
NO - GO TO 12.
9.CHECK MASS AIR FLOW SENSOR
Check both mass air flow sensor (bank 1) and mass air flow sensor (bank 2). P006A.
Is the inspection result normal?
YES - GO TO 10.
NO - Replace malfunctioning mass air flow sensor. Refer to . Exploded View.
10.CHECK PCV VALVE
Service and Repair.
Is the inspection result normal?
YES - GO TO 11.
NO - Repair or replace PCV valve. Exploded View.
11.CHECK INTERMITTENT INCIDENT
Perform Intermittent Incident.
Is the inspection result normal?
YES - GO TO 12.
NO - Repair or replace malfunctioning part.
12.REPLACE A/F SENSOR 1
Replace malfunctioning A/F sensor 1. Exploded View.
CAUTION:
- Discard any A/F sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
- Before installing new A/F sensor, clean exhaust system threads using Oxygen Sensor Thread
Cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant
(commercial service tool).
- INSPECTION END