P0AE7
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE
1.Turn ignition switch ON.
2.Check DTC.
Is DTC detected?
YES- Proceed to P0AE2.
NO- INSPECTION END
Diagnosis Procedure
WARNING:
- Because hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of electric shock, electric leakage, or similar accidents if the high voltage component and vehicle are handled incorrectly. Be sure to follow the correct work procedures when performing inspection and maintenance.
- Be sure to remove the service plug in order to shut off the high voltage circuits before performing inspection or maintenance of high voltage system harnesses and parts.
- Be sure to put the removed service plug in your pocket and carry it with you so that another person does not accidentally connect it while work is in progress.
- Be sure to wear insulating protective equipment consisting of glove, shoes and glasses before beginning work on the high voltage system.
- Clearly identify the persons responsible for high voltage work and ensure that other persons do not touch the vehicle. When not working, cover high voltage parts with an insulating cover sheet or similar item to prevent other persons from contacting them.
- High Voltage Precautions.
CAUTION:
There is the possibility of a malfunction occurring if the vehicle is changed to READY status while the service plug is removed. Therefore do not change the vehicle to READY status unless instructed to do so in the Service Manual.
1. CHECK DC/DC CONVERTER PRE-CHARGE SIGNAL CIRCUIT
With CONSULT
1.Select "HV PRE CHG RLY ACTIV" and "HV PRE CHG RLY ACTIV VOLT" in DATA MONITOR mode of
EV/HEV using CONSULT.
2.Check that monitor indication as per the following condition.
Without CONSULT
Check the voltage between HPCM harness connector and ground.
Is the inspection result normal?
YES- GO TO 2.
NO- GO TO 6.
2. CHECK DC/DC CONVERTER ACTIVATE SIGNAL
With CONSULT
1.Select "DC/DC CONV SIG VOLT" in DATA MONITOR mode of EV/HEV using CONSULT.
2.Check that monitor indication as per the following condition.
Without CONSULT
Check the voltage between HPCM harness connector and ground.
Is the inspection result normal?
YES- Perform Intermittent Incident.
NO- GO TO 3.
3. PRECONDITIONING
WARNING:
Shut off high voltage circuit. How to Cut Off High Voltage.
Check voltage in high voltage circuit. (Check that condenser are discharged.)
1.Remove trunk finisher front. Trunk Room Trim.
2.Remove harness cover (1).
3.Measure voltage between high voltage harness terminals.
CAUTION:
For voltage measurements, use a tester which can measure to 500 V or higher.
- GO TO 4.
4. CHECK DC/DC CONVERTER ACTIVATE SIGNAL-1
1.Turn ignition switch OFF.
2.Disconnect HPCM harness connector.
3.Disconnect Li-ion battery harness connector.
4.Check the continuity between HPCM harness connector and Li-ion battery harness connector.
5.Also check harness for short to ground and to power.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair or replace error-detected parts.
5. CHECK DC/DC CONVERTER ACTIVATE SIGNAL-2
1.Disconnect DC/DC converter harness connector.
2.Check the continuity between Li-ion battery harness connector and DC/DC converter harness connector.
3.Also check harness for short to ground and to power.
Is the inspection result normal?
YES- Replace DC/DC converter. DC/DC Converter Disassembly and Assembly.
NO- Repair or replace error-detected parts.
6. PRECONDITIONING
WARNING:
Shut off high voltage circuit. How to Cut Off High Voltage.
Check voltage in high voltage circuit. (Check that condenser are discharged.)
1.Remove trunk finisher front. Trunk Room Trim.
2.Remove harness cover (1).
3.Measure voltage between high voltage harness terminals.
CAUTION:
For voltage measurements, use a tester which can measure to 500 V or higher.
- GO TO 7.
7. CHECK DC/DC CONVERTER PRE-CHARGE SIGNAL CIRCUIT-1
1.Turn ignition switch OFF.
2.Disconnect Li-ion battery harness connector.
3.Check the continuity between HPCM harness connector and Li-ion battery harness connector.
4.Also check harness for short to ground and to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair or replace error-detected parts.
8. CHECK DC/DC CONVERTER PRE-CHARGE SIGNAL CIRCUIT-2
1.Disconnect DC/DC converter harness connector.
2.Check the continuity between Li-ion battery harness connector and DC/DC converter harness connector.
3.Also check harness for short to ground and to power.
Is the inspection result normal?
YES- Replace DC/DC converter. DC/DC Converter Disassembly and Assembly.
NO- Repair or replace error-detected parts.