Radio, Stereo, and Compact Disc: Description and Operation
AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: SYSTEM DIAGRAM
AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: SYSTEM DESCRIPTION
1. DISC PLAYER OUTLINE
(a) A disc player uses a laser pickup to read digital signals recorded on discs. By converting the digital signals to analog, music and other content can be played.
CAUTION:
Do not look directly at the laser pickup because the disc player uses an invisible laser beam. Be sure to operate the player only as instructed.
NOTICE:
- Do not disassemble any part of the disc player.
- Do not apply oil to the disc player.
- Do not insert anything but a disc into the disc player.
(b) Usable discs
(1) Disc player
This player can only play audio CDs, CD-Rs (CD-Recordable), CD-RWs (CD-ReWritable), DVD videos, audio DVDs, and video CDs that have any of the following marks:
(c) Precautions for handling disc
NOTICE:
- Copy-controlled CDs cannot be used.
- Some CD-Rs and CD-RWs are not playable as a result of: 1) the type of recording method used, 2) the type of disc, 3) scratches, 4) contamination, or 5) the disc being in the vehicle for an extended amount of time, leading to deterioration.
- CD-Rs and CD-RWs that have not been finalized cannot be played.
- PAL or SECAM color television standard discs cannot be played. Only NTSC discs can be played.
- Dual Discs that mate DVD recorded material on one side with CD digital audio material on the other cannot be played.
- When handling a disc, be careful not to put fingerprints, stains or scratches on the disc.
- When holding a disc, pinch the center hole and edge of the disc with your fingers. Face the printed side upward.
- If a disc is ejected by pressing the eject button and left partially ejected for an extended period of time, the disc may become deformed and unusable.
- A disc may not be able to be ejected or the player may become damaged if: 1) cellophane tape, stickers, CD-R labels or rental CD labels are attached; or 2) residue from removed tape, stickers or labels remains.
- Avoid direct sunlight when storing discs as they may become deformed and unusable.
- Do not use uniquely-shaped discs as they may damage the player.
- Do not use discs where part of the recording surface is transparent or translucent. If used, the disc may become unable to be inserted, ejected and played normally.
HINT:
- Just as condensation fogs the vehicle windows during wet or cold weather, condensation may also form inside the player. If condensation forms, disc skipping or playback stoppage may occur. Ventilate or dehumidify the vehicle for a while before using the player.
- If the player vibrates severely due to driving on a rough road, the disc may skip.
(d) Cleaning
NOTICE:
Do not use lens cleaner when cleaning the player, as it may damage the pickup part of the player.
(1) To clean dirty discs, use a dry, soft cloth such as those used for glasses with plastic lenses.
Lightly wipe radially from the center of the disc.
NOTICE:
- Pressing the disc roughly with your hand or scrubbing with a hard cloth may scratch the disc surface.
- Using record spray, antistatic agents, alcohol, benzene, thinner or other solvents, and chemical cloths on a disc will damage the disc and may make the disc unusable.
2. MP3/WMA OUTLINE
HINT:
Audio and visual systems of some vehicles do not support the WMA format.
(a) Playable MP3 file standards
(b) Playable WMA file standards
(c) ID3 tag and WMA tag
(1) Additional textual information called ID3 tags can be input to MP3 files. Information such as song titles and artist names can be stored.
HINT:
This player is compatible with the ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1).
(2) Additional textual information called WMA tags can be input to WMA files. Information such as song titles and artist names can be stored.
(d) Usable media
(1) Only CD-ROMs, CD-Rs (CD-Recordable), and CD-RWs (CD-ReWritable) can be used to play MP3/WMA files.
NOTICE:
- CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs may not be playable.
- If there are fingerprints or scratches on the disc, the disc may not be playable or the CD may skip.
- Some CD-Rs and CD-RWs deteriorate if they are left in the cabin for a long time.
- Keep CD-Rs and CD-RWs in a storage case that is non-transparent.
(e) Usable media format
(1) Usable media format
HINT:
- As for MP3/WMA files written in any format other than those above, the contents of the files may not be playable or the file names or folder names may not be displayed correctly.
- This player is compatible with multi-session discs and can play CD-Rs and CD-RWs on which MP3/WMA files are added. However, only the first session can be played.
- Discs whose first session includes both music data and MP3 or WMA format data cannot be played.
(2) Standards and restrictions
(f) File names
(1) Only files with an extension of ".mp3" or ".wma" can be recognized and played as MP3 or WMA files.
(2) Save MP3 or WMA files with an extension of ".mp3" or ".wma".
NOTICE:
If saving non-MP3 or non-WMA files with an extension of ".mp3" or ".wma", those files are wrongly recognized as MP3 or WMA files and played. A loud noise may occur and damage to the speakers may result.
3. "BLUETOOTH" OUTLINE
(a) "Bluetooth" is a new wireless connection technology that uses the 2.4 GHz frequency band. This makes it possible to connect a cellular phone ("Bluetooth" capable phone*) to the multi-display ("Bluetooth" system is built-in), and use a handsfree function with the cellular phone in a pocket or bag. As a result, it is not necessary to use a connector for the cellular phone.
HINT:
*: The communication performance of "Bluetooth" may vary depending on the "Bluetooth" version, obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity, or antenna capacity.
4. TOUCH SCREEN OUTLINE
(a) Touch switch
Touch switches are touch-sensitive (interactive) switches operated by touching the screen. When a switch is pressed, the outer glass bends into contact the inner glass at the pressed position. By doing this, the voltage ratio is measured and the pressed position is detected.
5. AVC-LAN DESCRIPTION
(a) What is AVC-LAN?
AVC-LAN, an abbreviation for "Audio Visual Communication Local Area Network", is a united standard developed by the manufacturers in affiliation with Toyota Motor Corporation. This standard pertains to audio and visual signals as well as switch and communication signals.
(b) Purpose:
Recently, car audio systems have rapidly developed and the functions have vastly changed. The conventional car audio system is being integrated with multimedia interfaces similar to those in navigation systems. At the same time, customers are demanding higher quality from their audio systems. This is an overview of the standardization background. The specific purposes are as follows:
(1) To solve sound problems, etc. caused by using components of different manufacturers through signal standardization.
(2) To allow each manufacturer to concentrate on developing the products they do best. From this, reasonably priced products can be produced.
HINT:
- If a short to +B or short to ground is detected in the AVC-LAN circuit, communication is interrupted and the audio system will stop functioning.
- If the audio system is equipped with a navigation system, the multi-display unit acts as the master unit Description and Operation.
- The radio receiver contains a resistor that is necessary to enable communication on the different AVC-LAN circuits.
- The car audio system with an AVC-LAN circuit has a diagnostic function.
- Each component has a specified number (3-digit) called a physical address. Each function has a number (2-digit) called a logical address.
6. COMMUNICATION SYSTEM OUTLINE
(a) Components of the audio system communicate with each other via the AVC-LAN.
(b) The master component of the AVC-LAN is a radio receiver with a 60 to 80 Ohms resistor. This is essential for communication.
(c) If a short circuit or open circuit occurs in the AVC-LAN circuit, communication is interrupted and the audio system will stop functioning.
7. DIAGNOSTIC FUNCTION OUTLINE
(a) The audio system has a diagnostic function. The result is indicated on the master unit.
(b) A 3-digit hexadecimal component code (physical address) is allocated to each component on the AVC-LAN. Using this code, the component can be displayed in the diagnostic function.
8. DIAGNOSIS DISPLAY DETAILED DESCRIPTION
HINT:
- This section contains a detailed description of displays within diagnostic mode.
- Illustrations may differ from the actual vehicle depending on the device settings and options. Therefore, some detailed areas may not be exactly the same as on the actual vehicle.
(a) SYSTEM CHECK
(1) System Check Mode Screen
- *1: Device Names and Hardware Address
HINT:
- Registered device names are displayed.
- If a device name is unknown to the system, its physical address is shown instead.
- *2: Check Result
HINT:
Result codes for all devices are displayed.
- *3: Code Clear
- Present DTCs are cleared.
- Press the "Code CLR" switch for 3 seconds.
- *4: Memory Clear
- Present and past DTCs and registered connected device names are cleared.
- Press the "Memory CLR" switch for 3 seconds.
(2) Diagnosis MENU Screen
HINT:
Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.
(3) Unit Check Mode Screen
Screen Description
(4) LAN Monitor (Original) Screen
- *: Check Result
HINT:
Check results of all the devices are displayed.
(5) LAN Monitor (Individual) Screen
Screen Description
(b) DISPLAY CHECK
(1) Vehicle Signal Check Mode Screen
Screen Description
HINT:
- Only items sending a vehicle signal will be displayed.
- This screen is updated once per second when input signals to the vehicle are changed.
(c) NAVIGATION CHECK
(1) Navigation Check Screen
HINT:
Some items may be grayed out or not displayed, as the functions are different depending on the vehicle.
(2) GPS Information Screen
- *1: Satellite information
Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.
- *2: Receiving condition
DENSO Model
AISIN AW Model
- *3: Measurement information
- *4: Position information
- *5: Date information
(3) Vehicle Sensors Screen
Vehicle Signal
Sensor Signal
HINT:
Signals are updated once per second only when vehicle sensor signals are changed.
(4) Mic & Voice Recognition Check Screen
Screen Description
HINT:
- The microphone input function is on at all times when this screen is displayed.
- While recording or playing, switches other than the stop switch cannot be pushed.
- When no voice is recorded, the play switch cannot be pushed.
- Recording will stop after 5 seconds or by pushing the stop switch.
(5) HDD Information Screen
Screen Description
Trouble Code Description
HINT:
This is the HDD check function in the navigation ECU.
(6) SMART Test Screen
1 In the HDD information screen, press the "SMART Test" button, and display the SMART Test result screen.
HINT:
- It takes approximately 90 seconds for the check to complete.
- If the SMART Test result is NG, the HDD is malfunctioning.
- If the temperature is low (less than -20°C (-4°F)) or high (65°C (149°F) or more), and the HDD cannot read or write, NG may be displayed.
(7) AVC-LAN Plus Check Screen
Screen Description
(8) AVC-LAN Plus Detail Screen
1 This screen shows the number and time of reconfigurations.
(9) AVC-LAN Plus Diagnosis Screen
Screen Description
(10) Sound Library Information Screen
Screen Description
(d) PROGRAM UPDATE
(1) Program Update Screen
1 This screen is used for program updates.
HINT:
For update procedures, view the new program disc contents and manual.