P2197
2GR-FE ENGINE CONTROL SYSTEM: SFI SYSTEM: P2195: Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
DTC P2195 - Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)
DTC P2196 - Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)
DTC P2197 - Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1)
DTC P2198 - Oxygen (A/F) Sensor Signal Stuck Rich (Bank 2 Sensor 1)
CAUTION / NOTICE / HINT
HINT:
- Although the DTC titles say oxygen sensor, these DTCs relate to the Air-Fuel Ratio (A/F) sensor.
- Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
DESCRIPTION
The A/F sensor generates a voltage* that corresponds to the actual air-fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air-fuel ratio. The ECM determines the deviation from the stoichiometric air-fuel ratio level, and regulates the fuel injection time. If the A/F sensor malfunctions, the ECM is unable to control the air-fuel ratio accurately.
The A/F sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are narrower than the conventional type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore the sensor activation is accelerated.
A three-way catalytic converter (TWC) is used in order to convert the carbon monoxide (CO), hydro carbon (HC), and nitrogen oxides (HOx) into less harmful substances. To allow the TWC to function effectively, it is necessary to keep the air-fuel ratio of the engine near the stoichiometric air-fuel ratio.
*: Value changes inside the ECM. Since the A/F sensor is the current output element, a current is converted to a voltage inside the ECM. Any measurements taken at the A/F sensor or ECM connectors will show a constant voltage.
HINT:
- DTCs P2195 and P2196 indicate malfunctions related to the bank 1 A/F sensor circuit.
- DTCs P2197 and P2198 indicate malfunctions related to the bank 2 A/F sensor circuit.
- Bank 1 refers to the bank that includes cylinder No. 1.
- Bank 2 refers to the bank that includes cylinder No. 2.
- When any of these DTCs are set, check the A/F sensor voltage output by selecting the following menu items on the intelligent tester: DIAGNOSIS / ENHANCED OBDII / DATA LIST / PRIMARY / AFS B1S1.
- Short-term fuel trim values can also be read using the intelligent tester.
- The ECM regulates the voltages at the A1A+, A2A+, A1A- and A2A- terminals of the ECM to a constant level. Therefore, the A/F sensor voltage output cannot be confirmed without using the intelligent tester.
- If an A/F sensor malfunction is detected, the ECM sets a DTC.
MONITOR DESCRIPTION
Sensor voltage detection monitor
- Under the air-fuel ratio feedback control, if the A/F sensor voltage output indicates rich or lean for a certain period of time, the ECM determines that there is a malfunction in the A/F sensor. The ECM illuminates the MIL and sets a DTC.
Example:
- If the A/F sensor voltage output is less than 2.8 V (very rich condition) for 10 seconds, despite the HO2 sensor voltage output being less than 0.6 V, the ECM sets DTC P2196. Alternatively, if the A/F sensor voltage output is more than 3.8 V (very lean condition) for 10 seconds, despite the HO2 sensor voltage output being 0.15 V or more, DTC P2195 is set.
Sensor current detection monitor
- A rich air-fuel mixture causes a low A/F sensor current, and a lean air-fuel mixture causes a high A/F sensor current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the A/F sensor current during fuel-cut and detects any abnormal current values.
- If the A/F sensor output is 3.6 mA or more for more than 3 seconds of cumulative time, the ECM interprets this as a malfunction in the A/F sensor and sets DTC P2195 (high-side stuck). If the A/F sensor output is 1.0 mA or less for more than 3 seconds of cumulative time, the ECM sets DTC P2196 (low-side stuck).
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
All:
Sensor voltage detection monitor (Lean side malfunction P2195, P2197):
Sensor voltage detection monitor (Rich side malfunction P2196, P2198):
Sensor Current detection monitor P2195, P2196, P2197 P2198
TYPICAL MALFUNCTION THRESHOLDS
Sensor voltage detection monitor (Lean side malfunction P2195, P2197):
Sensor voltage detection monitor (Rich side malfunction P2196, P2198):
Sensor current detection monitor (High side malfunction P2195, P2197):
Sensor current detection monitor (Rich side malfunction P2196, P2198):
MONITOR RESULT
Refer to CHECKING MONITOR STATUS Mode 6 Data.
WIRING DIAGRAM
CONFIRMATION DRIVING PATTERN
This confirmation driving pattern is used in steps 4, 7, 17, and 21 of the following diagnostic troubleshooting procedure when using the intelligent tester.
1. Connect the intelligent tester to the DLC3 (Procedure "A").
2. Turn the ignition switch to the ON position (Procedure "B").
3. Turn the tester on (Procedure "C").
4. Clear the DTCs DTC Check / Clear (Procedure "D").
5. Start the engine, and warm it up until the ECT reaches 70°C (158°F) or higher (Procedure "E").
6. Select the following menu items on the tester to check the fuel-cut status: DIAGNOSIS / ENHANCED OBD II / DATA LIST / USER DATA / FC IDLE (Procedure "F").
7. Drive the vehicle at between 38 mph (60 km/h) and 75 mph (120 km/h) for at least 10 minutes (Procedure "G").
8. Change the transmission to the 2nd gear (Procedure "H").
9. Drive the vehicle at a proper vehicle speed to perform fuel-cut operation (refer to the following HINT) (Procedure "I").
HINT: Fuel-cut is performed when the following conditions are met:
- Accelerator pedal is fully released.
- Engine speed is 2,500 rpm or more (fuel injection resumes at 1,000 rpm).
10. Accelerate the vehicle to 40 mph (64 km/h) or more by depressing the accelerator pedal for at least 10 seconds (Procedure "J").
11. Soon after performing procedure "J", release the accelerator pedal for at least 4 seconds without depressing the brake pedal, in order to execute fuel-cut control (Procedure "K").
12. Allow the vehicle to decelerate until the vehicle speed declines to less than 6 mph (10 km/h) (Procedure "L").
13. Repeat procedures from "H" through "K" in this section at least 3 times per driving cycle (Procedure "M").
HINT: Completion of all A/F sensor monitors is required to change the value in TEST RESULT.
CAUTION: Strictly observe posted speed limits, traffic laws, and road conditions when performing these driving patterns.
INSPECTION PROCEDURE
HINT: Malfunctioning areas can be identified by performing the A/F CONTROL function provided in the ACTIVE TEST. The A/F CONTROL function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
- The following instructions describe how to conduct the A/F CONTROL operation using an intelligent tester.
1. Connect the intelligent tester to the DLC3.
2. Start the engine and turn the tester on.
3. Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.
4. Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
5. Perform the A/F CONTROL operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
6. Monitor the voltage outputs of the A/F and HO2 sensors (AFS B1S1 and O2S B1S2 or AFS B2S1 and O2S B2S2) displayed on the tester.
HINT:
- The A/F CONTROL operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
- Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
Standard voltage:
NOTE: The Air-Fuel Ratio (A/F) sensor has an output delay of a few seconds and the Heated Oxygen (HO2) sensor has a maximum output delay of approximately 20 seconds.
PROCEDURE
1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195, P2196, P2197 OR P2198)
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Turn the tester on.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
(e) Read the DTCs.
Result:
HINT: If any DTCs other than P2195, P2196, P2197 or P2198 are output, troubleshoot those DTCs first.
B -- DTC CAUSED BY RUNNING OUT OF FUEL
A -- Continue to next step.
2. READ VALUE USING INTELLIGENT TESTER (TEST VALUE OF A/F SENSOR)
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch to the ON position and turn the tester on.
(c) Clear the DTCs DTC Check / Clear.
(d) Allow the vehicle to drive in accordance with the driving pattern described in the CONFIRMATION DRIVING PATTERN.
(e) Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / MONITOR INFO / MONITOR STATUS.
(f) Check that the status of O2S MON is COMPL.
If the status is still INCMPL, drive the vehicle according to the driving pattern again.
HINT:
- AVAIL indicates that the component has not been monitored yet.
- COMPL indicates that the component is functioning normally.
- INCMPL indicates that the component is malfunctioning.
(g) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / MONITOR INFO / TEST RESULT / RANGE B1S1, then press the ENTER button.
(h) Check the test value of the A/F sensor output current during fuel-cut.
Result:
B -- REPLACE AIR FUEL RATIO SENSOR
A -- Continue to next step.
3. READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF A/F SENSOR)
(a) Connect the intelligent tester to the DLC3.
(b) Start the engine.
(c) Turn the tester on.
(d) Warm up the Air-Fuel Ratio (A/F) sensor at an engine speed of 2,500 rpm for 90 seconds.
(e) Select the following menu items on the tester: DIAGNOSIS / ENHANCED OBD II / SNAPSHOT / MANUAL SNAPSHOT / USER DATA / AFS B1S1 or AFS B2S1 and ENGINE SPD.
(f) Check the A/F sensor voltage 3 times, when the engine is in each of the following conditions:
(1) While idling (check for at least 30 seconds) (Step (1))
(2) At an engine speed of approximately 2,500 rpm (without any sudden changes in engine speed) (Step (2))
(3) Raise the engine speed to 4,000 rpm and then quickly release the accelerator pedal so that the throttle valve is fully closed (Step (3)).
Standard voltage:
HINT: For more information, see the diagrams below.
HINT:
- If the output voltage of the A/F sensor remains at approximately 3.3 V (see Malfunction Condition diagram) under any conditions, including those described, the A/F sensor may have an open circuit. (This will also happen if the A/F sensor heater has an open circuit.)
- If the output voltage of the A/F sensor remains at either approximately 3.8 V or more, or 2.8 V or less (see Malfunction Condition diagram) under any conditions, including those described, the A/F sensor may have a short circuit.
- The ECM stops fuel injection (fuel cut) during engine deceleration. This causes a lean condition and results in a momentary increase in the A/F sensor output voltage.
- The ECM must establish a closed throttle valve position learning value to perform fuel cut. If the battery terminal has been reconnected, the vehicle must be driven over 10 mph (16 km/h) to allow the ECM to learn the closed throttle valve position.
- When the vehicle is driven:
The output voltage of the A/F sensor may be below 2.8 V during fuel enrichment. For the vehicle, this translates to a sudden increase in speed with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.
- The A/F sensor is a current output element; therefore, the current is converted into a voltage inside the ECM. Measuring the voltage at the connectors of the A/F sensor or ECM will show a constant voltage result.
NG -- INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
OK -- Continue to next step.
4. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
(a) Read DTCs using the intelligent tester.
(b) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
Result:
B -- CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
A -- Continue to next step.
6. REPLACE AIR FUEL RATIO SENSOR
(a) Replace the air fuel ratio sensor Removal.
NEXT -- Continue to next step.
7. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
(a) Read the DTCs using the intelligent tester.
(b) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
Result:
B -- REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A -- Continue to next step.
9. CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
NO -- CHECK FOR INTERMITTENT PROBLEMS
YES -- DTC CAUSED BY RUNNING OUT OF FUEL
10. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
(a) Disconnect the A4 or A3 A/F sensor connector.
(b) Measure the resistance between the terminals of the A/F sensor connector.
Standard resistance:
Bank 1
Bank 2
(c) Reconnect the A/F sensor connector.
NG -- REPLACE AIR FUEL RATIO SENSOR
OK -- Continue to next step.
11. INSPECT AIR FUEL RATIO SENSOR RELAY
(a) Remove the engine room junction block.
(b) Measure the A/F sensor heater relay resistance.
Standard resistance:
(c) Reinstall the engine room junction block.
NG -- REPLACE AIR FUEL RATIO SENSOR RELAY
OK -- Continue to next step.
12. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM)
(a) Disconnect the A3 or A4 A/F sensor connector.
(b) Turn the ignition switch to the ON position.
(c) Measure the voltage between the +B terminal of the A/F sensor connector and body ground.
Standard voltage:
(d) Turn the ignition switch off.
(e) Disconnect the E9 ECM connector.
(f) Measure the resistance between the terminals of A/F sensor connector and ECM connector.
Standard resistance :
Check for open
Check for short
(g) Reconnect the ECM connector.
(h) Reconnect the A/F sensor connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
13. CHECK AIR INDUCTION SYSTEM
(a) Check the air induction system for vacuum leakage.
OK:
No leakage from air induction system.
NG -- REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK -- Continue to next step.
14. CHECK FUEL PRESSURE
(a) Check the fuel pressure Testing and Inspection.
NG -- REPAIR OR REPLACE FUEL SYSTEM
OK -- Continue to next step.
15. INSPECT FUEL INJECTOR ASSEMBLY
(a) Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) Testing and Inspection.
NG -- REPLACE FUEL INJECTOR ASSEMBLY
OK -- Continue to next step.
16. REPLACE AIR FUEL RATIO SENSOR
(a) Replace the air fuel ratio sensor Removal.
NEXT -- Continue to next step.
17. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
18. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
(a) Read the DTCs using the intelligent tester.
(b) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
Result:
B -- REPLACE ECM AND PERFORM CONFIRMATION DRIVING PATTERN
A -- Continue to next step.
19. CONFIRM WHETHER VEHICLE HAS RUN OUT OF FUEL IN PAST
NO -- CHECK FOR INTERMITTENT PROBLEMS
YES -- DTC CAUSED BY RUNNING OUT OF FUEL
20. REPLACE AIR FUEL RATIO SENSOR
(a) Replace the air fuel ratio sensor Removal.
NEXT -- Continue to next step.
21. PERFORM CONFIRMATION DRIVING PATTERN
NEXT -- Continue to next step.
22. CHECK WHETHER DTC OUTPUT RECURS (DTC P2195, P2196, P2197 OR P2198)
(a) Connect the intelligent tester to the DLC3.
(b) Turn the ignition switch to the ON position and turn the tester on.
(c) Read the DTCs using the intelligent tester.
(d) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / PENDING CODES.
Result:
B -- REPLACE ECM
A -- END