Operation Check
LIGHTING (EXT): LIGHTING SYSTEM: OPERATION CHECK
1. BEFORE PERFORMING TROUBLESHOOTING
(a) Basic inspection
(1) Inspect the battery voltage.
Standard voltage:
11 to 14 V
(b) Visually inspect for burned out lights, blown fuses, open or shorted wire harnesses, malfunctioning or partially connected connectors, etc.
HINT
If the condition of a discharge headlight bulb cannot be determined through a visual check, replace it with a normally functioning bulb or interchange the left and right bulbs and check its condition.
2. INSPECT INTELLIGENT AFS SYSTEM
(a) With the vehicle stopped and the engine started, check that the leveling motor and swivel motor initialization (initial position setting) is performed.
HINT
For the swivel motor, only perform the vehicle inner side movement inspection (facing forward -> facing inner side -> facing forward).
(b) Based on the vehicle condition, check that the intelligent AFS system operation starts and stops accordingly.
3. INSPECT FRONT DOME LIGHT CONTROL OPERATION
HINT
The front dome light control illuminates the lights below.
* Map light assembly
(a) With the engine switch off, and all doors closed and locked, unlock a door. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.*1
(b) With the engine switch off and all doors closed, open and close a front door. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.
(c) With all doors closed, turn the engine switch on (IG) or on (ACC), or turn the engine switch from on (IG) to off. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.*2
(d) For *1 and *2, before the lights listed above turn off, open a front door. Check that the illumination continues. Then close the door and check that the lights remain illuminated for approximately 15 seconds from when the door was closed.
(e) With the engine switch off and the lights listed above illuminated based on the timer control (approximately 15 seconds), close and lock all doors, or turn the engine switch on (IG) or on (ACC). Check that the lights turn off.
4. INSPECT REAR ROOM LIGHT CONTROL OPERATION
HINT
The rear dome light control illuminates the lights below.
* No. 1 room light assembly
* No. 3 room light assembly
(a) With the engine switch off, and all doors closed and locked, unlock a door. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.*1
(b) With the engine switch off and all doors closed, open and close a rear door. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.
(c) With all doors closed, turn the engine switch on (IG) or on (ACC), or turn the engine switch from on (IG) to off. Check that the lights listed above illuminate for approximately 15 seconds, and then turn off.*2
(d) For *1 and *2, before the lights listed above turn off, open a rear door. Check that the illumination continues. Then close that door and check that the lights remain illuminated for approximately 15 seconds.
(e) With the engine switch off and the lights listed above illuminated based on the timer control (approximately 15 seconds), close and lock all doors, or turn the engine switch on (IG) or on (ACC). Check that the lights turn off.
5. INSPECT MAP LIGHT CONTROL
HINT
The related light is listed below.
* Map light assembly
(a) Check that the map light turns on when the engine switch is turned on (ACC).
(b) Check that the map light turns off when the engine switch is turned off.
6. INSPECT INTERIOR FOOT LIGHT CONTROL
HINT
The related lights are listed below.
* No. 1 interior illumination light assembly LH (front interior foot light LH)
* No. 1 interior illumination light assembly RH (front interior foot light RH)
* Interior illumination light assembly RH (rear interior foot light RH)
* Interior illumination light assembly LH (rear interior foot light LH)
(a) Check that either condition described below illuminates the interior foot light.
(1) A door is opened.
(2) The engine switch is turned on (IG) and the shift lever is moved to P.
(b) Check that the condition described below dims the interior foot light.
(1) The engine switch is turned on (IG) and the shift lever is moved to a position other than P.
(c) Check that the condition described below illuminates the interior foot light for approximately 15 seconds, and then turns off the interior foot light.
(1) With the engine switch off and a door open, the door is closed.
(d) Check that the condition described below turns off the interior foot light.
(1) With the engine switch off, all doors are closed and locked.
7. INSPECT INSIDE HANDLE ILLUMINATION LIGHT CONTROL
HINT
The related lights are listed below.
* Front door inside handle illumination light assembly LH
* Front door inside handle illumination light assembly RH
* Rear door inside handle illumination light assembly LH
* Rear door inside handle illumination light assembly RH
(a) Check that either of the conditions described below illuminates the inside handle illumination light.
(1) A door is opened.
(2) The engine switch is turned on (IG) and the shift lever is moved to P.
(b) Check that the condition described below dims the inside handle illumination light.
(1) The engine switch is turned on (IG) and the shift lever is moved to a position other than P.
(c) Check that the condition described below illuminates the inside handle illumination light for approximately 15 seconds, and then turns off the inside handle illumination light.
(1) With the engine switch off and a door open, the door is closed.
(d) Check that the condition described below turns off the inside handle illumination light.
(1) With the engine switch off, all doors are closed and locked.
8. INSPECT COURTESY LIGHT CONTROL
HINT
The related lights are listed below.
* Front door courtesy light assembly LH
* Front door courtesy light assembly RH
* Rear door courtesy light assembly LH
* Rear door courtesy light assembly RH
* Scuff plate illumination LH (w/ Illumination Type Front Door Scuff Plate)
* Scuff plate illumination RH (w/ Illumination Type Front Door Scuff Plate)
(a) Check that the condition described below illuminates the courtesy light.
(1) A door is opened.
(b) Check that the condition described below turns off the courtesy light.
(1) A door is closed.
9. INSPECT STEP LIGHT CONTROL
HINT
The related lights are listed below.
* Step light assembly LH
* Step light assembly RH
(a) Check that the condition described below illuminates the step light.
(1) A door is opened.
(b) Check that the condition described below turns off the step light.
(1) A door is closed.
(c) Check that the conditions described below illuminate the step light for approximately 15 seconds, and then turns off the step light.
(1) The key enters the smart key certification area.
(2) With the engine switch off, all the doors are closed and locked.
(3) With the engine switch on (IG) and the shift lever in P, perform an unlock operation using the door lock switch of the driver door or passenger door.
10. INSPECT DOOR MIRROR FOOT LIGHT CONTROL
NOTICE:
Perform this inspection with the customize parameter at the initial setting.
HINT
The related lights are listed below.
* Door mirror foot light LH
* Door mirror foot light RH
(a) Check that any of the conditions described below illuminates the foot light for approximately 15 seconds, and then turns off the foot light.
(1) The key enters the smart key certification area.
(2) With the engine switch off, all doors are closed and locked.
(3) With the engine switch on (IG) and the shift lever in P, perform an unlock operation using the door lock switch of the driver door or passenger door.
(b) Check that either of the conditions described below turns off the foot light.
(1) With the engine switch on (IG), the shift lever is moved from P to a position other than P.
(2) A wireless, entry or key-linked lock operation is performed.
11. INSPECT AUTOMATIC LIGHT CONTROL SYSTEM OPERATION
NOTICE:
Perform this inspection with the customize parameter at the initial setting.
(a) Turn the engine switch on (IG).
(b) Set the headlight dimmer switch assembly to AUTO.
(c) Slowly cover the automatic light control sensor with a lightproof object, and check that the lights automatically illuminate.
OK:
Clearance lights illuminate, and then headlights illuminate
(d) After illuminating the light, slowly move the lightproof object off of the automatic light control sensor and check that the lights automatically turn off.
OK:
Headlights turn off, and then clearance lights turn off
12. INSPECT AUTOMATIC LIGHT CONTROL SYSTEM (ILLUMINATION, TURN OFF)
(a) Make the area around the automatic light control sensor dark to automatically illuminate the head lights.
(b) Check that any of the conditions described below turns off the head lights.
(1) The headlight dimmer switch assembly is turned off.
(2) The surrounding area of the automatic light control sensor is brightened.
(3) With the engine switch off, the driver door is opened.
(c) Make the area around the automatic light control sensor dark to automatically illuminate the head lights.
(d) With the engine switch off, open the driver door to turn off the head lights.
(e) When the engine switch is turned on (IG), check that the head lights turn on again.
13. INSPECT LIGHT AUTO TURN OFF SYSTEM
(a) Prepare the vehicle so that the engine switch is on (IG) and the driver door is closed.
(b) Set the headlight dimmer switch assembly to tail, head or AUTO to illuminate the head lights.
(c) Turn the engine switch off, and then open the driver door. Check that the headlight and taillights turn off.
14. INSPECT BATTERY SAVER
HINT
The related lights are listed below.
* Front door inside handle illumination light assembly LH
* Front door inside handle illumination light assembly RH
* Rear door inside handle illumination light assembly LH
* Rear door inside handle illumination light assembly RH
* No. 1 interior illumination light assembly LH (front interior foot light LH)
* No. 1 interior illumination light assembly RH (front interior foot light RH)
* Interior illumination light assembly LH (rear interior foot light LH)
* Interior illumination light assembly RH (rear interior foot light RH)
* Door mirror foot light LH
* Door mirror foot light RH
* Step light assembly LH
* Step light assembly RH
* Engine switch illumination
* Map light assembly
* No. 1 room light assembly (w/ Rear Seat Entertainment System)
* No. 1 room light assembly (w/o Rear Seat Entertainment System)
* No. 3 room light assembly
(a) With a door open and the engine switch on (ACC), check that the illumination turns off after approximately 20 minutes.