Instrument Panel, Gauges and Warning Indicators: Description and Operation
METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM:
1. BEAN SIGNAL
2. CAN AND AVC-LAN SIGNAL
3. DIRECT LINE SIGNAL
4. INPUT AND OUTPUT SIGNALS OF THE COMBINATION METER
- *1: w/ Intuitive Parking Assist System
- *2: w/ Pre-collision System
- *3: w/ Sliding Roof
- *4: w/ Dynamic Radar Cruise Control System
- *5: w/o Navigation System
- *6: w/ Navigation System
- *7: for U.S.A.
- *8: for Canada
METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: SYSTEM DESCRIPTION
1. OUTLINE OF THE COMBINATION METER
(a) Meter/Gauge
(b) Warning/Indicator
- *1: w/o Navigation System
- *2: w/ Navigation System
- *3: for U.S.A.
- *4: for Canada
- *5: w/ Pre-collision System
(c) Multi-information Display
HINT:
- The multi-information display is located in the upper center of the combination meter.
- The display shows a message or animation for each of the functions described in the table below.
- *1: w/ Intuitive Parking Assist System
- *2: w/ Dynamic Radar Cruise Control System
(d) ODO/TRIP Display
- *: for U.S.A.
2. MULTI-INFORMATION DISPLAY FLOW CHART
(a) Multi-information display flow chart
(b) Each warning indication in English
HINT: Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle.
(c) Each warning indication in French
HINT: Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle.
3. VOLTAGE METER
(a) The voltage meter displays the battery voltage using one bar. If the battery voltage is too low (below 10 V), the first bar will blink to inform the driver. If the voltage is too high (17 V or higher), the seventh bar will blink. When turning the engine switch on (IG), the meter CPU determines the battery voltage based on the power source voltage supplied to it.
4. ENGINE OIL TEMPERATURE GAUGE
(a) The meter CPU uses the engine oil temperature sensor to determine the temperature of the engine oil. The resistance of the engine oil temperature sensor will vary between approximately 30 kOhms or higher with the engine oil temperature is 0°C (32°F), and approximately 0.3 kOhms with the engine oil temperature is 155°C (311°F). Voltage measured at this point will vary as the engine temperature is changed.
The engine oil temperature gauge displays the engine oil temperature using seven bars. The meter CPU calculates the engine oil temperature based on signals from the engine oil temperature sensor via the direct line. When the engine oil temperature becomes 140°C (284°F) or higher, all the bars blink and the warning message is displayed in the multi-information display.
HINT:
- If the circuit is open, the lowest bar blinks.
- If the circuit is shorted, all the bars blink and engine oil temperature warning light comes on.
5. DIAGNOSIS SYSTEM
(a) Display example for English
(b) Display example for French
(c) The combination meter indicates diagnosis mode by blinking the warning light or the warning message in the multi-information display.
HINT:
- The multi-information display shows "DIAG" when the engine switch is on (IG) Test Mode Procedure.
- Diagnosis information can be displayed on the multi-information display after connecting a jumper wire between TC (J21-13) and CG (J21-4) of the DLC3 connector.
6. SATELLITE SWITCH
(a) By using the satellite switch (RH switch, ON/OFF switch, LH switch), 3 different switch functions can be displayed and changed (Tire pressure, Sonar*, AFS).
- *: w/ Intuitive Parking Assist System
HINT:
- When the engine switch on (IG) while driving at 3 mph (5 km/h) or less, the switch except for SONAR can be displayed as shown in the illustration below.
- The switch functions displayed are changed in the order shown in the illustration using the satellite switch (RH switch, LH switch). The function can be set using the ON/OFF switch.
- The display automatically returns to the previous display 6 seconds after the satellite switch is operated. It will return to the previous display immediately if the DISP switch is operated.
(1) Display example for English
(2) Display example for French
7. LED INITIAL CHECK
(a) The illumination function of the warning, indicator, or reminder light listed below can be confirmed when turn the engine switch on (IG).
OK:
