EVAP Control System Pressure Sensor For California
P0451 EVAP CONTROL SYSTEM PRESSURE SENSOR
Description
The EVAP control system pressure sensor detects pressure in the purge line. The sensor output voltage to the ECM increases as pressure increases.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
Never remove fuel filler cap during DTC confirmation procedure.
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
With CONSULT-GO TO 2.
Without CONSULT-GO TO 5.
2. PERFORM DTC CONFIRMATION PROCEDURE-1
With CONSULT
1.Start engine and let it idle for least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure".
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE-2
With CONSULT
1.Select "EVAP DIAG READY" in "DATA MONITOR" mode of "ENGINE".
2.Let it idle until "OFF" of "EVAP DIAG READY" changes to "ON".
NOTE:
It will take at most 2 hours until "OFF" of "EVAP DIAG READY" changes to "ON".
3.Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
4.Turn ignition switch ON.
5.Select "EVAP LEAK DIAG" in "DATA MONITOR" mode of "ENGINE".
6.Check that "EVAP LEAK DIAG" indication.
Which is displayed on CONSULT?
CMPLT- GO TO 4.
YET- 1.Perform DTC CONFIRMATION PROCEDURE again.
2.GO TO 1.
4. PERFORM DTC CONFIRMATION PROCEDURE-3
With CONSULT
Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure".
NO- INSPECTION END
5. PERFORM DTC CONFIRMATION PROCEDURE-4
With GST
1.Start engine and let it idle for least 40 seconds.
NOTE:
Do not depress accelerator pedal even slightly.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure".
NO- GO TO 6.
6. PERFORM DTC CONFIRMATION PROCEDURE-5
With GST
1.Let it idle for at least 2 hours.
2.Turn ignition switch OFF and wait at least 90 minutes.
NOTE:
Never turn ignition switch ON during 90 minutes.
3.Turn ignition switch ON.
4.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Proceed to "Diagnosis Procedure".
NO- INSPECTION END
Diagnosis Procedure
1. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace ground connection.
2. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR CONNECTOR FOR WATER
1.Disconnect EVAP control system pressure sensor harness connector.
2.Check sensor harness connector for water.
Water should not exist.
Is the inspection result normal?
YES- GO TO 3.
NO- Repair or replace harness connector.
3. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR POWER SUPPLY CIRCUIT
1.Turn ignition switch ON.
2.Check the voltage between EVAP control system pressure sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 8.
NO- GO TO 4.
4. CHECK SENSOR POWER SUPPLY CIRCUITS
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair short to ground or short to power in harness or connectors.
5. CHECK COMPONENTS
Check the following.
- Crankshaft position sensor (POS) (CKP Sensor (POS) For California.)
- Refrigerant pressure sensor (Refrigerant Pressure Sensor.)
- Tumble control valve position sensor (P2004.)
Is the inspection result normal?
YES- GO TO 6.
NO- Replace malfunctioning component.
6. CHECK APP SENSOR
APP Sensor For California.
Is the inspection result normal?
YES- GO TO 9.
NO- GO TO 7.
7. REPLACE ACCELERATOR PEDAL ASSEMBLY
Replace accelerator pedal assembly. Removal And Installation.
- INSPECTION END
8. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
Refer to "Component Inspection".
Is the inspection result normal?
YES- GO TO 9.
NO- Replace EVAP control system pressure sensor. Removal And Installation.
9. CHECK INTERMITTENT INCIDENT
Intermittent Incident.
- INSPECTION END
Component Inspection
1. CHECK EVAP CONTROL SYSTEM PRESSURE SENSOR
1.Turn ignition switch OFF.
2.Remove EVAP control system pressure sensor with its harness connector connected from EVAP canister.
Removal And Installation.
Always replace O-ring with a new one.
3.Install a vacuum pump to EVAP control system pressure sensor.
4.Turn ignition switch ON and check output voltage between ECM harness connector and ground under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace EVAP control system pressure sensor. Removal And Installation.