Information Display
SYSTEM
INFORMATION DISPLAY : System Description
SYSTEM DIAGRAM
Combination Meter Input Signal (CAN Communication)
DESCRIPTION
- The information display is an LCD positioned inside the combination meter. It is used to inform the driver of a variety of vehicle information.
- The combination meter receives the signals required to control the operation of the information display from each unit, switch, and sensor.
- Based on the received signals, the combination meter displays the following information on the information display.
- Odo/trip meter
- Shift indicator
- Trip computer
- Interrupt indication
- Warning check indication
- Setting
- Timer status remained display
- Charging time display
- Meter illumination control
- ASCD status display
- The information display screen is divided into sections (A) - (C), and the items displayed in each section are different.
NOTE:
If there are no items to display in display section (A), the items in display section (B) are displayed larger.
- Pressing the switch (enter switch) changes the item displayed in display section (B) in the following sequence.
"Charging time" "Average electricity consumption/Current electricity consumption" "Average vehicle speed"
"Travel Distance/Travel Time" "Setting" "Warning"
ASCD STATUS DISPLAY
Based on the signals listed below, the combination meter displays the ASCD status.
For details, refer to "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : System Description" Automatic Speed Control Device (ASCD).
TRIP COMPUTER
Based on the signals received from each unit, switch, and sensor, the combination meter displays the items shown below.
- Current electricity consumption
- Average electricity consumption
- Average vehicle speed
- Travel distance
- Travel time
Current Electricity Consumption
The combination meter calculates current electricity consumption based on the following signals, and the calculated value is displayed on the information display.
NOTE:
- Current electricity consumption on the information display is updated approximately every 0.5 seconds.
- Current electricity consumption on the information display shows 0 kWh/km (0 kWh/miles) when vehicle speed is 0 km/h (0 MPH).
Average Electricity Consumption
The combination meter calculates average electricity consumption based on the following signals, and the calculated value is displayed on the information display.
NOTE:
Average electricity consumption on the information display is updated approximately every 30 seconds.
Average Vehicle Speed
The combination meter calculates average vehicle speed based on the following signals, and the calculated value is displayed on the information display.
NOTE:
- Average vehicle speed on the information display is updated approximately every 30 seconds.
- Soon after a reset or when the power switch is turned READY right after battery removal and installation, "" is displayed until after a 30 seconds.
Travel Distance
The combination meter calculates mileage, based on the following signals and displays the mileage on the information display.
Travel Time
The combination meter measures and displays travel time (power switch ON time).
CHARGING TIME DISPLAY
Based on the signals below, the combination meter displays the charge time.
INTERRUPT INDICATION
- The combination meter displays an interrupt regarding a warning, alert, and maintenance on the information display, based on signals received from each unit and switch.
- When conditions are satisfied, the normal screen switches to a warning screen to display an interrupt.
Interrupt Display Items
Push Start Display
- The combination meter judges showing/hiding of "push start display", according to the signal below.
- For the display items and conditions, refer to "WARNING FUNCTION : System Description" Warning Function.
- When the charge connector is connected, the "pug in indicator" is displayed.
Remove Charge Connector Warning Display
- When turning the power switch ON or changing the READY to driving mode with the charge connector connected, "Charge connecter removal warning" may be displayed.
- The combination meter judges showing/hiding of the "remove charge connector warning", according to the signal below.
Door Open Warning
- When all the following operating conditions are satisfied, the combination meter displays a "door open warning" on the information display by an interrupt.
- The combination meter judges showing/hiding of "door open warning", according to the signal below.
Electric Shift Warning
- If a malfunction occurs in the electronic shift system, the "electric shift warning" is displayed.
- The combination meter judges showing/hiding of "electric shift warning", according to the signal below.
Li-ion Battery Low Charge Warning
- When the battery remaining energy is 4 kWh or less, the "Li-ion battery low charge warning" is displayed.
(low battery charge warning lamp turns ON and warning is displayed.)
- The combination meter judges showing/hiding of "Li-ion batter low charge warning", according to the signal below.
Power Limitation Warning
- When drive power is 40 kW or less, the "power limitation display" is displayed.
- The combination meter judges showing/hiding of "power limitation display", according to the signal below.
Electric Parking Brake Warning
- If a malfunction occurs in the electric parking brake system, the "electric parking brake warning" is displayed.
- The combination meter judges showing/hiding of "electric parking brake warning", according to the signal below.
- For the display items and conditions, refer to "System Description" System.
Light Reminder Warning
- When all of the following conditions are met, the combination meter displays the "light reminder warning".
- Based on the following signals, BCM judges "light reminder warning" and sends the buzzer output signal (light reminder warning) to the combination meter via CAN communications.
- The combination meter judges showing/hiding of "light reminder warning", according to the signal below.
Check Tire Pressure Warning
The combination meter judges showing/hiding of "check tire pressure warning", according to the signal below.
DC/DC Converter Warning
- If a malfunction occurs in the DC/DC converter system, the "DC/DC converter warning" is displayed.
- The combination meter judges showing/hiding of "DC/DC converter warning", according to the signal below.
Intelligent Key System Warning
- If a malfunction occurs in the Intelligent Key system, the "Intelligent Key system warning" is displayed.
- The combination meter judges showing/hiding of "Intelligent Key system warning", according to the signal below.
Low Washer Fluid Warning
- When all the following operating conditions are satisfied, the combination meter displays a low washer fluid warning on the information display by an interrupt.
- The combination meter judges showing/hiding of "low washer fluid warning", according to the signals below:
Driver alert (Alarms)
- When all the following operating conditions are satisfied, the combination meter displays a driver alert on the information display by an interrupt.
- The combination meter judges showing/hiding of "driver alert", according to the signal below:
Outside temp (Alarms)
- When all the following operating conditions are satisfied, the combination meter displays a outside temp on the information display by an interrupt.
- The combination meter cancels the warning of "outside temp" when the following cancel condition is satisfied.
- For outside air temperature display, refer to "OUTSIDE AIR TEMPERATURE DISPLAY : System
Description".
- The combination meter judges showing/hiding of "outside temp", according to the signals below:
Tire (Maintenance)
- When all the following operating conditions are satisfied, the combination meter displays a tire warning on the information display by an interrupt.
- The combination meter judges showing/hiding of "tire warning", according to the signals below:
Other 1, Other 2, Other 3 (Maintenance)
- When all the following operating conditions are satisfied, the combination meter displays an other warning on the information display by an interrupt.
- The combination meter judges showing/hiding of "other warning", according to the signals below:
Meter Illumination Level Indication
When receiving the following signals, the combination meter causes an interrupt on the information display to indicate an illumination level.
TIMER STATUS REMINDER DISPLAY
- The combination meter receives the next charge time signal, next departure time signal or next pre-A/C time signal when the power switch is READY and displays the timer charging after the power switch is turned
OFF.
- Pressing the switch (enter switch) changes the displayed item in the following sequence.
Timer charging ON/OFF, timer A/C ON/OFF Next charge start time / end time Charging time Timer
A/C start time
- If no switches are operated for 10 seconds, the display screen turns OFF.
- The combination meter judges showing/hiding of the "timer status reminder display" according to the signals below.
WARNING CHECK INDICATION
- The combination meter can cause an interrupt on the information display to indicate a warning, based on signals received from each unit and switch.
- The indicated warning can be checked with "WARNING" during the satisfaction of an interrupt indication condition for each warning.
Warning Display Items
- Door open warning
- Electric shift warning
- Power limitation warning
- Li-ion battery low charge warning
- Electric parking brake warning
- Take away warning (push start display)
- Intelligent Key system warning
SETTING
Warning indication timing and time can be set.
Clock
Setting values for "Set clock", and "24/12 Hr" can be adjusted to meet the user's needs.
Maintenance
Setting values for tire and other maintenance items can be adjusted to meet the user's needs.
Alarms
Setting values for "Driver Alert", and "Outside Temp" can be adjusted to meet the user's needs.
Units
Setting values for "TEMPERATURE" and "SPEED" items can be adjusted to meet the user's needs.
Language
Setting values for "Language" items can be adjusted to meet the user's needs.
Effects
Setting values for "Effects" items can be adjusted to meet the user's needs.
For the effects function, refer to "START UP SOUND SYSTEM : System Description" Start Up Sound System.
Factory
Allows the user to reset all settings other than the odometer.
Settings-reject Indication
- Regarding settings-reject indications, "SETTING CAN BE OPERATED WHEN STOPPED" is shown on the information display when indication conditions are satisfied.
- When reaching 5 km/h (3.1 MPH) after accelerating from a stopping condition, a settings-reject indication is displayed.
- When reaching less than 1 km/h (0.6 MPH) after decelerating from 5 km/h (3.1 MPH), a settings-reject indication is cancelled to allow settings.
- The combination meter judges a vehicle condition based on the following signals and displays a settingsreject indication on the information display.
ODO/TRIP METER
The combination meter calculates mileage, based on the following signals and displays the mileage on the information display.
SHIFT INDICATOR
The combination meter displays the shift position based on the signals below.
