P2127
P2127, P2128 APP SENSOR
Description
The accelerator pedal position sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the ECM.
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometer which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors sends opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM
judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM
receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for engine operations such as fuel cut.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE
1.Start engine and let it idle for 1 second.
2.Check DTC.
Is DTC detected?
YES- Go to .
NO- INSPECTION END
Diagnosis Procedure
Regarding Wiring Diagram information, [1][2]Electrical Diagrams.
1. CHECK GROUND CONNECTION
1.Turn ignition switch OFF.
2.Check ground connection E9. Refer to Ground Inspection in Circuit Inspection.
Is the inspection result normal?
YES- GO TO 2.
NO- Repair or replace ground connection.
2. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-I
1.Disconnect accelerator pedal position (APP) sensor harness connector.
2.Turn ignition switch ON.
3.Check the voltage between APP sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 6.
NO- GO TO 3.
3. CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT-II
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between APP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES- GO TO 4.
NO- Repair open circuit.
4. CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair short to ground or short to power in harness or connectors.
5. CHECK COMPONENTS
Check the following.
- Crankshaft position sensor (POS) (P0335.)
- EVAP control system pressure sensor (P0451.)
- Refrigerant pressure sensor (Refrigerant Pressure Sensor.)
Is the inspection result normal?
YES- GO TO 10.
NO- Replace malfunctioning components.
6. CHECK APP SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between APP sensor harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 7.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
7. CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Check the continuity between APP sensor harness connector and ECM harness connector.
2.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 8.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
8. CHECK APP SENSOR
.
Is the inspection result normal?
YES- GO TO 10.
NO- GO TO 9.
9. REPLACE ACCELERATOR PEDAL ASSEMBLY
1.Replace accelerator pedal assembly.
2.Special Repair Requirement
- INSPECTION END
10. CHECK INTERMITTENT INCIDENT
Intermittent Incident.
- INSPECTION END
Component Inspection
1. CHECK ACCELERATOR PEDAL POSITION SENSOR
1.Reconnect all harness connectors disconnected.
2.Turn ignition switch ON.
3.Check the voltage between ECM harness connector terminals under the following conditions.
Is the inspection result normal?
YES- INSPECTION END
NO- GO TO 2.
2. REPLACE ACCELERATOR PEDAL ASSEMBLY
1.Replace accelerator pedal assembly.
2.Go to P2138.
- INSPECTION END
Special Repair Requirement
1. PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
Special Repair Requirement.
- GO TO 2.
2. PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Special Repair Requirement.
- GO TO 3.
3. PERFORM IDLE AIR VOLUME LEARNING
Special Repair Requirement.
- END