Catalytic Converter Replacement - Left Side (6.0L Engine)

Catalytic Converter Replacement - Left Side (6.0L Engine)

Removal Procedure

1. Disconnect the battery ground cable from the battery. Refer to Battery Negative Cable Disconnection and Connection (Service and Repair) .




Caution: Refer to Exhaust Service Caution (Service Precautions) .
Caution: Refer to Protective Goggles and Glove Caution (Protective Goggles and Glove Warning) .

Important: The left catalytic converter to exhaust manifold retaining nuts (1) are single use parts. They must be discarded after removal.


2. Remove the left catalytic converter to exhaust manifold retaining nuts (1).
Discard the nuts.
3. Disconnect the left catalytic converter (2) from the exhaust manifold (3).
Caution: Refer to Vehicle Lifting Caution (Service Precautions) .
4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (Service and Repair) .





Notice: Refer to Heated Oxygen and Oxygen Sensor Notice (Heated Oxygen and Oxygen Sensor Notice) .

5. Disconnect the left pre-catalytic converter heated oxygen sensor (HO2S) electrical connector (1).





Important: The intermediate exhaust assembly to left catalytic converter retaining nuts (3) are single use parts. They must be discarded after removal.


6. Remove the intermediate exhaust assembly to left catalytic converter retaining nuts (3).
Discard the nuts.
7. Disconnect the intermediate exhaust assembly (2) from the left catalytic converter (1).




8. Remove the left catalytic converter (1) from the vehicle.
9. Remove the left pre-catalytic converter HO2S. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (Service and Repair) .



Installation Procedure

1. Install the left pre-catalytic converter HO2S to the left catalytic converter. Refer to Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (Service and Repair) .




Caution: Refer to Exhaust Service Caution (Service Precautions) .

Important: Make sure that a new sealing ring is fitted prior to installation. Failure to comply may cause the exhaust system to perform poorly.


2. Install the left catalytic converter (1) to the vehicle.




3. Align the intermediate exhaust assembly (2) to the left catalytic converter (1) by pushing back and down on the intermediate exhaust assembly (2).




4. Push up and forward on the left catalytic converter (2) to connect to the exhaust manifold (3).
5. Lower the vehicle.
6. Install the left catalytic converter to exhaust manifold retaining nuts (1).
7. Tighten the left catalytic converter to exhaust manifold retaining nuts (1).

Tighten the nuts to 45 N.m (33 lb ft).

Caution: Refer to Vehicle Lifting Caution (Service Precautions) .
8. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (Service and Repair) .




9. Install the intermediate exhaust assembly to left catalytic converter retaining nuts (3).

Notice: Refer to Fastener Notice (Fastener Notice) .

10. Tighten the intermediate exhaust assembly to left catalytic converter retaining nuts (3).

Tighten the nuts to 40 N.m (30 lb ft).





11. Connect the left pre-catalytic converter HO2S electrical connector (1).
12. Make sure that the exhaust system is clear of all other components and chassis. If the exhaust system is not clear of all the other components loosen all retaining nuts and re-align. Refer to Exhaust System Alignment (LY7 and L98 Engines) (Service and Repair) .
13. Lower the vehicle to the ground.
14. Connect the battery ground cable to the battery. Refer to Battery Negative Cable Disconnection and Connection (Service and Repair) .
15. If re-programming is required. Refer to Control Module References (Programming and Relearning) .
16. Perform diagnostic system check using diagnostic scan tool, clear all relative DTCs and inspect the system for correct operation.