197019 Removing and installing radiator
WM 197019 Removing and installing radiator
Technical values
Preliminary work
Preliminary work for removing radiator
WARNING
Hot fluid
- Danger of scalding
-> Let the fluid cool down.
-> Wear personal protective gear.
1. Remove front apron.
-> 631519 Removing and installing front apron 631519 Removing and installing front spoiler.
2. Drain coolant at the radiators.
-> 193817 Draining and filling in coolant (includes bleeding) 193817 Draining and filling in coolant.
3. Remove air guides in front of the radiators.
-> 192419 Removing and installing air guide Service and Repair.
Information
The air-conditioning condenser remains in the vehicle. The air-conditioning system is not opened.
4. Detach air-conditioning condenser from side radiator and allow it to hang freely.
4.1. To do this, remove hexagon-head tapping screw between the air-conditioning condenser and side radiator and pull air-conditioning condenser out of the side brackets.
Removing radiator
Installation position
1. Remove the vent line at the top of the side radiator. To do this, press the lock and pull the line off the support -1-. Pull the vent line out of the holder -2-.
Vent line
2. Remove cable plug from fan motor -arrow-. To do this, press cable plug together (relieve plug), open the release and disconnect the cable plug.
Cable plug
3. Remove M6 x 16 fastening screw (external Torx) on hose holder -arrow-.
Attachment for hose holder
WARNING
Hot fluid
- Danger of scalding
-> Let the fluid cool down.
-> Wear personal protective gear.
WARNING
Caustic fluids
- Danger of chemical burns
-> Avoid contact with caustic fluid.
-> Wear personal protective gear.
-> Ensure that there is good ventilation.
-> If you do come into contact, wash off immediately with plenty of warm water and contact a doctor if necessary.
Information
Despite the fact that the coolant has been drained, residual amounts of coolant can still emerge at the joints during removal. Have sufficient collecting containers and cloths to hand.
4. Disconnect the two coolant hoses from the supports for the side radiator -arrows-. To do this, loosen the spring-band clamps from the front and push them onto the supports.
Radiator connections
5. Open up the coolant hoses at the supports using a screwdriver and allow the coolant hoses to drain -arrow-. Pull coolant hoses off the supports.
Draining coolant
6. Remove M8 x 25 fastening screw on bracket from below at the body -arrow-.
Lower fastening screw
7. Undo two M8 fastening nuts on the bracket in the wheel housing at the side wall -arrows-. Carefully remove side radiator complete with bracket to the side. Collect remaining coolant from the hoses and side radiator. Air-conditioning condenser remains in installation position.
Fastening nuts
8. When the side radiator is removed, remove the sheetmetal clips and washers for the bracket -arrows-. Carefully pull the side radiator upwards out of the bracket.
Bracket for side radiator
9. Remove two hexagon-head sheetmetal screws at the side -1- and lift cooling fan housing with rear air guide out of the tabs on the side radiator -2-.
Cooling fan
Installing radiator
Information
The air-conditioning condenser remains in the vehicle. The air-conditioning system is not opened.
Installation position
1. Fit cooling fan housing with rear air guide on side radiator. To do this, push side tabs of cooling fan housing into the brackets for the side radiator -2- , move housing into installation position and fit with two fastening screws -1-.
Cooling fan
2. Push radiator module into the radiator bracket. Make sure that the radiator is positioned correctly in the side guide and in the lower bores. Fit washers and sheetmetal clips on the lower fastening pins of the radiator in such a way that the sheetmetal clips engage correctly into the pins -arrows-.
Bracket for side radiator
3. Move side radiator with bracket into installation position. Make sure that the hose holder for the coolant hoses is inserted correctly into the side bracket. Push side radiator with bracket on to the studs on the side member and insert fastening screw M6 x 16 (external Torx) for the hose holder -arrow-.
Securing hose holder
4. Position the M8 fastening nuts on the body studs -arrows-.
Fastening nuts
5. Fit fastening screws to the body from below => Tightening torque: 23 Nm (17 ftlb.) -arrow-.
Lower fastening screw
6. Tighten the fastening nuts on the body studs => Tightening torque: 23 Nm (17 ftlb.). Tighten fastening screw M6 x 16 (external Torx) for hose holder => Tightening torque: 10 Nm (7.5 ftlb.).
7. Push spring band clamps on to radiator flanges and fit radiator hoses to the flanges. Move engaged spring band clamps into installation position and loosen using a water-pump pliers (use a screwdriver as well, if necessary) and then fasten again -arrows-.
Radiator connections
8. Fit radiator vent line to the flange -1- and clip vent line into the plastic holder -2-.
Vent line
9. Connect cable plug for fan motor -arrow-.
Cable plug
Subsequent work
Subsequent work for installing radiator
1. Fit the air guide in front of the radiators.
-> 192419 Removing and installing air guide Service and Repair.
2. Fill in coolant and check the system for leaks.
-> 193817 Draining and filling in coolant (includes bleeding) 193817 Draining and filling in coolant.
-> 19010100 Checking cooling system.
3. Install front apron.
-> 631519 Removing and installing front apron 631519 Removing and installing front spoiler.