697719 Removing and installing frame for roll-over protection system
WM 697719 Removing and installing frame for roll-over protection system
Technical values
Preliminary work
1. Removing rear wall trim panel -> 703119 Removing and installing trim panel for rear wall - section on "Removing" 703119 Removing and installing rear wall trim panel
2. Remove cover for the rear. -> 705319 Removing and installing cover for rear - section on "Removing" 705319 Removing and installing rear cover.
3. Remove rear side trim panel at left and right. -> 707519 Removing and installing rear side trim panel - section on "Removing" 707519 Removing and installing rear side trim panel
4. Undo seat belt and rear mounting component at the left and right. -> 691219 Removing and installing rear three-point belt - section on "Removing"
5. Trigger the roll-over bar. -> 697219 Removing and installing roll-over bar - section on "Removing" 697219 Removing and installing roll-over bar
Information
Do not loosen hydraulic lines at hydraulic pump.
6. Remove hydraulic pump and set it aside. -> 618419 Removing and installing hydraulic pump - section on "Removing" Service and Repair
7. Unlock plug connections for DME control module. -> 247019 Removing and installing DME control module - section on "Removing"
8. Unlock plug connections for convertible-top control unit. -> 619619 Removing and installing control unit for convertible top - section on "Removing" Service and Repair
9. Release relay carrier and set it aside. -> 979019 Removing and installing relay carrier - section on "Removing" 979009 Removing and installing relay carrier
10. Remove motor for drive mechanism and set it aside. -> 617019 Removing and installing motor for drive mechanism - section on "Removing" 61701900 Removing and installing convertible-top compartment lid drive
Removing frame for roll-over protection system
Installation position of frame for roll-over protection system
1. Press in locking tabs -arrows A- and pull plug connections -1- off wire harness for roll-over protection system -arrow B-.
Disconnecting plug connections
2. Unscrew fastening screw -1- and fastening nuts -2- from Z support -3-.
Removing frame for roll-over protection system
3. Unscrew fastening screws -4- and carefully remove frame for roll-over protection system -5- upwards out of the vehicle.
Installing frame for roll-over protection system
Installation position of frame for roll-over protection system
1. Carefully position frame for roll-over protection system -5- on the vehicle. Screw in fastening screws -1, 4- and fastening nuts partially by hand.
Removing frame for roll-over protection system
Information
To reduce adjustment work to a minimum when assembling convertible-top components, the frame for the roll-over protection system must be positioned according to the dimension shown.
2. Move frame for roll-over protection system -5- to adjust it by dimension -X- => Adjustment value: 491 mm+/-1 mm.
Adjusting frame for roll-over protection system
3. Screw in fastening screw -1- and fastening nuts -2- on rear Z support -3-. Tightening torque => Tightening torque: 45 Nm (33 ftlb.) => Tightening torque: 45 Nm (33 ftlb.)
4. Screw down fastening screw -4- on frame for roll-over protection system -5-. Tightening torque => Tightening torque: 45 Nm (33 ftlb
5. Press in plug connections -1- on wire harness for roll-over protection system.
Locking plug connection
Diagram of frame for roll-over protection system
Diagram of frame for roll-over protection system
Subsequent work
1. Secure motor for convertible-top compartment lid drive. -> 617019 Removing and installing motor for drive mechanism - section on "Installing" 61701900 Removing and installing convertible-top compartment lid drive
2. Push relay carrier into its retaining frame and engage firmly. -> 979019 Removing and installing relay carrier - section on "Installing" 979009 Removing and installing relay carrier
3. Lock plug connections for convertible-top control unit. -> 619619 Removing and installing control unit for convertible top - section on "Installing" Service and Repair
4. Lock plug connections for DME control module. -> 247019 Removing and installing DME control module - section on "Installing"
5. Install hydraulic pump. -> 618419 Removing and installing hydraulic pump - section on "Installing" Service and Repair
6. Secure seat belt and rear mounting component at the left and right. -> 691219 Removing and installing rear three-point belt - section on "Installing"
7. Install rear side trim panel at left and right. -> 707519 Removing and installing rear side trim panel - section on "Installing" 707519 Removing and installing rear side trim panel
8. Press in roll-over bar and perform a function test on the roll-over protection modules. -> 697219 Removing and installing roll-over bar - section on "Installing" 697219 Removing and installing roll-over bar
9. Install cover for rear. -> 705319 Removing and installing cover for rear- section on "Installing" 705319 Removing and installing rear cover.
10. Install trim panel for rear wall -> 703119 Removing and installing trim panel for rear wall - section on "Installing" 703119 Removing and installing rear wall trim panel