Fuel System: Precaution
2AZ-FE FUEL: FUEL SYSTEM: PRECAUTION
1. BEFORE WORKING ON FUEL SYSTEM
(a) Do not work near an open flame.
(b) Keep gasoline away from rubber and leather parts.
(c) Discharge the fuel pressure before disconnecting the fuel line to prevent gasoline from spilling out. Refer to the following procedure.
2. DISCHARGE FUEL SYSTEM PRESSURE
CAUTION:
* The DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
* After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.
(a) Remove the rear seat cushion with cover pad subassembly Removal.
(b) Remove the rear seat under tray cover Removal.
(c) Remove the bench type rear seat cushion assembly Removal.
(d) Remove the rear door scuff plate RH Removal.
(e) Remove the rear door scuff plate LH Removal.
(f) Remove the rear floor service hose cover.
(g) Disconnect the connector.
(h) Start the engine. After the engine stops naturally, turn the ignition switch off.
HINT
DTC P0171 (system too lean) may be set.
(i) Start the engine again and make sure that engine does not start.
(j) Remove the fuel tank cap, and let the air out of the fuel tank.
(k) Connect the connector.
(l) Install the rear floor service hole cover with new butyl tape.
(m) Install the rear door scuff plate RH Installation.
(n) Install the rear door scuff plate LH Installation.
(o) Install the bench type rear seat cushion assembly Installation.
(p) Install the rear seat under tray cover Installation.
(q) Install the rear seat cushion with cover pad subassembly Installation.
3. FUEL SYSTEM
(a) When disconnecting the high-pressure fuel line, a large amount of gasoline will spray out. So take the following precautions:
(1) Discharge the fuel system pressure.
(2) Disconnect the fuel tube.
(3) Drain the fuel remaining inside the fuel pump tube into a container.
(4) Do not damage the disconnected pipe or connector, and prevent entry of foreign matter by covering them with plastic bags.
(b) Observe the following precautions when removing and installing the fuel injector.
(1) Do not reuse the O-ring and insulator.
(2) When placing a new O-ring onto the injector, do not damage the O-ring.
(3) Coat the new O-ring with grease or gasoline before installing it. Do not use engine, gear or brake oil.
(c) Install the injector into the delivery pipe and cylinder head, as shown in the illustration. Apply grease or gasoline to the contact surfaces of the injector before installing the injector.
(d) Observe the following precautions when disconnecting the fuel delivery pipe (metallic type).
HINT
The structure of the fuel tube connector is as shown in the illustration.
(1) Check if there is any damage or foreign matter on the connecting parts of the pipes.
(2) Remove the EFI fuel pipe clamp.
(3) Find the metallic connector of the fuel tube assembly.
(4) Assemble SST to the connection as shown in the illustration.
SST : 09268-21011
(5) Turn SST, align the retainers inside the connector with the SST chamfered parts and insert SST into the connector.
(6) Slide SST and the connector together towards the fuel tube assembly.
(e) Observe the following precautions when connecting the fuel tube connector (metallic type).
(1) Check if there is any damage or foreign matter on the connecting part of the pipe.
(2) Match the axis of the connector with the axis of the pipe, and push into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of clean engine oil to the tip of the pipe.
(3) After finishing the connection, check if the pipe and the connector are securely connected by pulling on them.
(4) Install a EFI fuel pipe clamp.
(5) Inspect for fuel leaks.
(f) Observe the following precautions when disconnecting the fuel tube connectors (Quick Type A).
(1) Release the claw and remove the EFI fuel pipe clamp.
(2) Check that there is no dirt or other foreign matter on the pipe and around the connector before disconnecting them. Clean them if necessary.
(3) Pinch the fuel tube connector, and then disconnect the fuel tube.
NOTICE:
Do not use any tools.
(4) Drain the fuel remaining inside the fuel tube.
(5) Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.
(g) Observe the following precautions when connecting the fuel tube connectors (Quick Type A).
(1) Check if there is any damage or foreign matter on the connecting parts of the pipes.
(2) Line up the two parts of the pipes to be connected, and push them together until the connector makes a "click" sound. If the pipe is difficult to push into the connector, apply a small amount of clean engine oil to the tip of the pipe and reinsert it.
(3) After connecting the pipes, check that the pipe and connector are securely connected by pulling on them.
(4) Engage the lock claws and install the EFI fuel pipe clamp.
(5) Inspect for fuel leaks.
4. INSPECT FOR FUEL LEAK
(a) Check that there is no fuel leakage after performing maintenance anywhere on the fuel system ( Fuel System).