Reassembly

DOOR / HATCH: BACK DOOR: REASSEMBLY

REASSEMBLY

1. INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY Installation
2. INSTALL ROOF HEADLINING ASSEMBLY
HINT: Refer to the procedure from Install Roof Headlining Assembly Installation.

3. INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY Installation
4. INSTALL REAR WIPER MOTOR GROMMET Installation
5. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY Installation
6. INSTALL REAR WIPER ARM HEAD CAP Installation
7. INSTALL REAR WASHER NOZZLE Installation
8. INSPECT REAR WASHER NOZZLE Washer Nozzle (for Rear Side)
9. ADJUST REAR WASHER NOZZLE Washer Nozzle (for Rear Side)
10. INSTALL REAR SPOILER ASSEMBLY Installation
11. INSTALL LICENSE PLATE LIGHT ASSEMBLY Installation
12. INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
13. INSTALL REAR LIGHT ASSEMBLY LH Installation
14. INSTALL REAR LIGHT ASSEMBLY RH
HINT: Use the same procedure for the RH side and LH side.

15. INSTALL AMPLIFIER ANTENNA ASSEMBLY Installation
16. INSTALL POWER BACK DOOR WARNING BUZZER (w/ Power Back Door) Installation
17. INSTALL BACK DOOR LOWER DAMPER STAY BRACKET LH Installation
18. INSTALL BACK DOOR LOWER DAMPER STAY BRACKET RH
HINT: Use the same procedure for the RH side and LH side.

19. INSTALL BACK DOOR STAY ASSEMBLY LH Installation
20. INSTALL BACK DOOR STAY ASSEMBLY RH
HINT: Use the same procedure for the RH side and LH side.

21. INSTALL POWER BACK DOOR TOUCH SENSOR ASSEMBLY LH (w/ Power Back Door) Installation
22. INSTALL POWER BACK DOOR TOUCH SENSOR ASSEMBLY RH (w/ Power Back Door)
HINT: Use the same procedure for the RH side and LH side.

23. INSTALL BACK DOOR LOCK ASSEMBLY (w/o Easy Closer)
(a) Apply MP grease to the sliding parts of the back door lock assembly.
(b) Apply adhesive to the threads of the bolt.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(d) Connect the connector.
(e) Engage the clamp.
24. INSTALL BACK DOOR LOCK ASSEMBLY (w/ Easy Closer)
(a) Apply MP grease to the sliding parts of the back door lock assembly.
(b) Apply adhesive to the threads of the bolt.
Adhesive:
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(d) Install the bolt.
Torque: 8.0 Nm (82 kgf-cm, 71in-lbf)
(e) Engage the clamp.
(f) Connect the connector.
25. INSTALL POWER BACK DOOR CLOSER SWITCH ASSEMBLY (w/ Power Back Door) Installation
26. INSTALL DOOR PULL HANDLE

(a) Engage the 4 claws to install the back door pull handle.
27. INSTALL BACK DOOR TRIM COVER RH

(a) Engage the 2 clips to install the back door trim cover RH.
28. INSTALL UPPER BACK DOOR STAY BRACKET LH

(a) Install the upper back door stay bracket LH with the 2 bolts.
Torque: 13 Nm (133 kgf-cm, 10ft-lbf)
29. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)

(a) Engage the 2 clips to install the back door trim cover LH.
30. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)

(a) Engage the 2 clips to install the back door trim cover LH.
31. CONNECT POWER BACK DOOR ROD (w/ Power Back Door)

(a) Install the stop ring to the power back door rod.

(b) Install the power back door rod.
32. INSTALL BACK DOOR PANEL TRIM ASSEMBLY

(a) Engage the 16 clips and install the back door panel trim assembly.
33. INSTALL UPPER BACK WINDOW PANEL TRIM

(a) Engage the 4 clips and 4 claws to install the upper back window panel trim.