DTC Troubleshooting
DTC Troubleshooting: P0AC2 (114)
DTC P0AC2:
Battery Current Sensor 1 Circuit High Voltage
NOTE:
- Before you troubleshoot, record all freeze data, and any on-board snapshot, and review the general troubleshooting information Initial Inspection and Diagnostic Overview.
- If the DTC cannot be cleared, do the troubleshooting for DTC U1204.
1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Start the engine.
4. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0AC2 indicated?
YES -
Go to step 5.
NO -
Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the MCM and the battery current sensor.
5. Turn the ignition switch to LOCK (0).
6. Turn the battery module switch OFF.
7. Remove the IPU cover IPU Cover Removal/Installation.
8. Remove the PCU lid, the PCU busplate, and the PCU cover Service and Repair.
9. Disconnect MCM connector B (24P).
10. Turn the ignition switch to ON (II).
11. Measure the voltage between MCM connector terminal B3 and body ground.
Is there 4.5 V or more?
YES -
Repair a short to power in the wire between the battery current sensor and the MCM (B3), then go to step 20.
NO -
Go to step 12.
12. Clear the DTC with the HDS.
13. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0AC2 indicated?
YES -
Go to step 26.
NO -
Go to step 14.
14. Turn the ignition switch to LOCK (0).
15. Reconnect MCM connector B (24P).
16. Check for continuity between MCM connector terminal B14 and body ground.
Is there continuity?
YES -
Go to step 17.
NO -
Go to step 26.
17. Disconnect MCM connector B (24P).
18. Disconnect the junction board 12P connector (A).
19. Check for continuity between junction board 12P connector terminal No. 2 and MCM connector terminal B14.
Is there continuity?
YES -
Replace the battery module Service and Repair, then go to step 20.
NO -
Repair an open in the wire between the junction board 12P connector and the MCM (B14), then go to step 20.
20. Reconnect all connectors.
21. Reinstall the PCU cover, the PCU busplate, and the PCU lid Service and Repair.
22. Reinstall the IPU cover IPU Cover Removal/Installation, then turn the battery module switch ON.
23. Turn the ignition switch to ON (II).
24. Clear the DTC with the HDS.
25. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0AC2 indicated?
YES -
Check for poor connections or loose terminals at the MCM and the battery current sensor, then go to step 1.
NO -
Troubleshooting is complete. If any other Pending or Confirmed DTCs are indicated, go to the indicated DTC's troubleshooting.
26. Reconnect all connectors.
27. Reinstall the PCU cover, the PCU busplate, and the PCU lid Service and Repair.
28. Reinstall the IPU cover IPU Cover Removal/Installation, then turn the battery module switch ON.
29. Update the MCM if it does not have the latest software Testing and Inspection, or substitute a known-good MCM.
30. Turn the ignition switch to ON (II).
31. Check for Pending or Confirmed DTCs with the HDS.
Is DTC P0AC2 indicated?
YES -
Check for poor connections or loose terminals at the MCM and the battery current sensor. If the MCM was updated, substitute a known-good MCM, then recheck. If the MCM was substituted, go to step 1.
NO -
If the MCM was updated, troubleshooting is complete. If the MCM was substituted, replace the original MCM Service and Repair. If any other Pending or Confirmed DTCs were indicated, go to the indicated DTC's troubleshooting.