97551900 Removing and installing wire harness for convertible top
WM 975519 Removing and installing wire harness for convertible top
Technical values
Preliminary work
Preliminary work for convertible top wiring harness
1. Remove convertible-top covering. -> 612819 Removing and installing convertible top covering - section on "Removing" 612819 Removing and installing hood covering
Preliminary work for wiring harness for roll-over protection system
1. Disconnect battery. -> 271000 Work instructions after disconnecting the battery
2. Remove roll-over bar. -> 697219 Removing and installing roll-over bar - section on "Removing" 697219 Removing and installing roll-over bar
Removing wire harness for convertible top
Removing plastic panel
Installation position of convertible top wire harness
1. Remove plastic panel.
Removing plastic panel
1.1. Unscrew fastening screws -4- and remove plastic bracket -2- from roof frame 1 -3-.
1.2. Turn fixing clip -1- 90° counterclockwise and remove to the rear from the plate of the plastic panel -2-.
Disconnecting wire harness plug connection for convertible top
1. Release electric plug connection -1- of wire harness -Arrow a- and disconnect.
Disconnecting wire harness plug connection for convertible top
Removing wire harness for convertible top
1. Remove wire harness at rear window.
Removing wire harness at rear window
1.1. Pull off both connectors -2- at the rear window -Arrows A-.
1.2. Pull out wire harness -1- from the rear window frame -Arrow B-.
1.3. Unscrew the two fastening screws -3- and remove the wire harness -1- from the fabric plate -4-.
2. Remove wire harness convertible top support.
Removing wire harness convertible top support
2.1. Remove the three tie-wraps -2-.
2.2. Unscrew the two fastening screws -3-.
2.3. Unclip wire harness -1- from the two retaining clips -Arrows A-.
2.4. Remove foam part -4- -Arrow B-.
3. Remove potentiometer.
Removing potentiometer
3.1. Remove wire harness -1- from the two clamps -2-.
3.2. Unscrew the two fastening screws -3- and remove the potentiometer -4-.
4. Remove wire harness from cable duct.
Removing wire harness from cable duct
4.1. Remove wire harness -1- from cable duct -2-.
5. Removing wire harness at roof frame 1 and roof frame 3
Removing wire harness at roof frame 1 and roof frame 3
5.1. Unscrew the two fastening screws -3- and remove plastic bracket -2- on roof frame 3 -5-.
5.2. Unclip wire harness -1- at roof frame 3 -5- and at roof frame 1 -4-.
Removing wire harness for roll-over protection system
Overview of plugs for wire harness for roll-over protection system
1. Release and disconnect plug connections for rear side panel flap -2- at left and right. -> 614219 Removing and installing rear side section flap - section on "Removing" Service and Repair
2. Release and disconnect plug connection for hardtop mount -3-. -> 611719 Removing and installing hardtop mount - section on "Removing" 611719 Removing and installing hardtop fastening
3. Release connector on convertible top control unit -6- and pull off. -> 619619 Removing and installing control unit for convertible top - section on "Removing" Service and Repair
4. Release and disconnect plug connection for roll-over protection system wire harness to rear wire harness -7-. -> 697719 Removing and installing frame for roll-over protection system - section on "Removing" 697719 Removing and installing frame for roll-over protection system
5. Release plug connection on motor for convertible-top compartment lid drive -8- and disconnect. -> 617019 Removing and installing drive motor - section on "Removing" 61701900 Removing and installing convertible-top compartment lid drive
6. Unclip and remove wire harness for roll-over protection system -1- at the retaining clips -4-.
Installing wire harness for convertible top
1. Install wire harness at roof frame 1 and roof frame 3.
Installing wire harness at roof frame 1 and roof frame 3
1.1. Lay wire harness -1- and clip in at roof frame 1 -4- and at roof frame 3 -5-.
1.2. Position plastic bracket -2- on roof frame 3 -8- and screw down with the two fastening screws -3-. => Tightening torque: 3 Nm (2 ftlb.)
2. Press wire harness into cable duct.
Pressing wire harness into cable duct
2.1. Press wire harness into cable duct.
3. Install potentiometer.
Installing potentiometer.
3.1. Insert potentiometer fork into the pins of the hydraulic housing.
3.2. Position potentiometer -4- on convertible top support and screw down with the two fastening screws -3-. => Tightening torque: 3 Nm (2 ftlb.)
3.3. Lay wire harness -1- and press into the two clamps -2-.
4. Install wire harness on convertible-top support.
Installing wire harness on convertible-top support
4.1. Lay wire harness -1- and insert foam part -4- -Arrow A-.
4.2. Clip in wire harness -1- at the two retaining clips -Arrows B-.
4.3. Secure wire harness -1- with the two fastening screws -3-.
4.4. Fit three new tie-wraps -2-.
5. Install wire harness at rear window.
Installing wire harness at rear window
5.1. Push wire harness -1- through the fabric plate -4- -Arrow A- and secure with the two fastening screws -3-.
5.2. Lay wire harness -1- and press into the rear window frame -Arrow B-.
5.3. Push on both connectors -2- at the rear window -Arrows C-.
Connecting wire harness plug connection for convertible top
1. Push together the electric plug connection -1- of the wire harness until it is felt to engage.
Connecting wire harness plug connection for convertible top
Installing plastic panel
1. Install plastic panel.
Installing plastic panel
1.1. Insert fixing clip -1- onto plate of plastic panel from behind -2- and turn 90° clockwise.
1.2. Position plastic panel -2- on roof frame 1 -3- and screw down with the fastening screws -4-. Tightening torque => Tightening torque : 5 Nm (3.5 ftlb.)
Installing wire harness for roll-over protection system
Overview of plugs for wire harness for roll-over protection system
1. Position wire harness for roll-over protection system -1- on the frame and clip in at the retaining clips -4-.
2. Press motor plug connection for convertible-top compartment lid drive -8- together until it is felt to engage. -> 617019 Removing and installing drive motor - section on "Removing" 61701900 Removing and installing convertible-top compartment lid drive
3. Push together plug connection for roll-over protection system wire harness to rear wire harness -7- until it is felt to engage. -> 697719 Removing and installing frame for roll-over protection system - section on "Installing" 697719 Removing and installing frame for roll-over protection system
4. Connect connector to convertible top control unit -6- and lock it until it engages firmly. -> 619619 Removing and installing control unit for convertible top - section on "Installing" Service and Repair
5. Push in hardtop mount plug connection -3- until it engages securely. -> 611719 Removing and installing mount for hardtop - section on "Installing" 611719 Removing and installing hardtop fastening
6. Push in plug connections for rear side panel flap -2- at left and right until it is felt to engage. -> 614219 Removing and installing rear side section flap - "Installing" section Service and Repair
Subsequent work
Subsequent work for convertible top wiring harness
1. Install convertible-top covering. -> 612819 Removing and installing convertible top covering - section on "Installing" 612819 Removing and installing hood covering
Subsequent work for wiring harness for roll-over protection system
1. Install roll-over bar. -> 697219 Removing and installing roll-over bar - section on "Installing" 697219 Removing and installing roll-over bar
2. Carry out work instructions after disconnecting the battery. -> 271000 Work instructions after disconnecting the battery