C0215
BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: C0210/33,C0215/34,C1238/38,C1239/39: Rear Speed Sensor RH Circuit
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD, BA, VSC, A-TRAC, CRAWL and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.
To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.
HINT
- DTC C0210/33 and C1238/38 are for the rear speed sensor RH.
- DTC C0215/34 and C1239/39 are for the rear speed sensor LH.
WIRING DIAGRAM
INSPECTION PROCEDURE
NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration Programming and Relearning.
PROCEDURE
1. READ VALUE USING TECHSTREAM (RR/RL SPEED OPEN)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG) and turn the Techstream on.
(c) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
ABS/VSC/TRAC
(d) Check for any momentary interruption in the wire harness and connector corresponding to the DTC Check for Intermittent Problems.
OK:
There are no momentary interruptions.
HINT
Perform the above inspection before removing the sensor and connector.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM (RR/RL WHEEL SPEED, RR/RL WHEEL DIRECTION)
(a) Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
ABS/VSC/TRAC
OK:
The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed.
(b) Check that the sensor signal conforms to the wheel direction.
ABS/VSC/TRAC
OK:
The wheel direction is displayed correctly.
NG -- INSPECT REAR SPEED SENSOR INSTALLATION
OK -- Continue to next step.
3. PERFORM SIGNAL CHECK
(a) Check if test mode (signal check) DTCs are output.
HINT
Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
Result
B -- RECONFIRM DTC
A -- Continue to next step.
4. INSPECT REAR SPEED SENSOR INSTALLATION
(a) Check the speed sensor installation.
OK:
The installation nut is tightened properly.
There is no clearance between the sensor and rear axle.
Torque : 8.3 Nm (85 kgf-cm, 73 in-lbf)
NOTICE:
Check the speed sensor signal after replacement Scan Tool Testing and Procedures.
NG -- INSTALL REAR SPEED SENSOR CORRECTLY
OK -- Continue to next step.
5. INSPECT SPEED SENSOR TIP
(a) Remove the rear speed sensor Removal.
(b) Check the sensor tip.
OK:
No scratches or foreign matter on the sensor tip.
NOTICE:
Check the speed sensor signal after cleaning/replacement Scan Tool Testing and Procedures.
NG -- CLEAN OR REPLACE REAR SPEED SENSOR Removal
OK -- Continue to next step.
6. INSPECT REAR SPEED SENSOR
(a) Install the rear speed sensor.
(b) Disconnect the z19 and/or z20 rear speed sensor connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
for LH
NG -- REPLACE REAR SPEED SENSOR Removal
OK -- Continue to next step.
7. INSPECT SKID CONTROL SENSOR WIRE
(a) Disconnect the z19/z20 and Nz1 skid control sensor wire connectors.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
for LH
NOTICE:
Check the speed sensor signal after replacement Scan Tool Testing and Procedures.
NG -- REPLACE SKID CONTROL SENSOR WIRE Removal
OK -- Continue to next step.
8. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - SKID CONTROL SENSOR WIRE)
(a) Disconnect the A24 skid control ECU connector and Nz1 skid control sensor connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for RH
for LH
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
9. INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)
(a) Reconnect the A24 skid control ECU connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
for RH
for LH
NG -- REPLACE MASTER CYLINDER SOLENOID
OK -- Continue to next step.
10. RECONFIRM DTC
(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.
(b) Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
(c) Check if the same DTCs are output Reading and Clearing Diagnostic Trouble Codes.
HINT
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result
C -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Problem Symptoms Table
B -- USE SIMULATION METHOD TO CHECK How To Proceed With Troubleshooting
A -- Continue to next step.
11. REPLACE REAR SPEED SENSOR
(a) Replace the rear speed sensor Removal.
NOTICE:
Check the speed sensor signal after replacement Scan Tool Testing and Procedures.
NEXT -- Continue to next step.
12. RECONFIRM DTC
(a) Clear the DTCs Reading and Clearing Diagnostic Trouble Codes.
(b) Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.
(c) Check if the same DTCs are output Reading and Clearing Diagnostic Trouble Codes.
HINT
Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
Result
B -- END
A -- Continue to next step.
13. INSPECT SPEED SENSOR ROTOR
(a) Remove the rear axle hub and bearing assembly Service and Repair.
(b) Check the sensor rotor.
OK:
No scratches, oil, or foreign matter on the rotors.
NOTICE:
Check the speed sensor signal after cleaning/replacement Scan Tool Testing and Procedures.
NG -- CLEAN OR REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (SPEED SENSOR ROTOR)
OK -- REPLACE MASTER CYLINDER SOLENOID