Removal And Installation
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
CAUTION:
- Disconnect both the negative and positive battery terminals, then wait at least three minutes.
- Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
- Be careful not to scratch pad and other parts.
INSTRUMENT PANEL ASSEMBLY
Removal
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
Broken square indicates Metal clip
Broken circle indicates Pawl
2. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
Broken square indicates Metal clip
Broken circle indicates Pawl
3. Remove cluster lid C.
a. Remove the upper screws from cluster lid C.
b. Pull cluster lid C backward while disengaging the metal clips and pawl.
c. Disconnect harness connector, and then remove cluster lid C.
4. Remove audio unit. Removal And Installation Audio Without Navigation (Audio without Navigation) or Removal And Installation Audio With Navigation, "Removal and Installation" (Audio with Navigation).
5. Remove front pillar garnish. Component.
Broken circle indicates Pawl
6. Remove the instrument side panel (LH/RH).
a. Pull up instrument side panel and disengage pawls.
b. Remove instrument side panel.
Broken circle indicates Pawl
7. Remove instrument side mask (LH/RH).
a. Insert a suitable tool into upper space of instrument side mask.
b. Disengage pawls, and then remove instrument side mask.
Broken square indicates Metal clip
8. Remove instrument side finisher.
a. Insert a suitable tool into space of instrument side finisher.
b. Disengage instrument side finisher metal clips, and then remove instrument side finisher.
Broken circle indicates Pawl
9. Remove side ventilator assembly (LH).
a. Insert a suitable tool into the bottom gap of side ventilator assembly and push against (A) and (B) as shown to disengage the pawls.
Broken circle indicates Pawl
b. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator.
10. Remove steering lock escutcheon.
11. Remove the steering column cover screws, then disengage pawls and remove the steering column covers.
12. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.
Broken square indicates Metal clip
Broken triangle indicates Clip
b. Lift the instrument upper panel up, disengage metal clips.
c. Pull backward and disengage clips.
d. Remove cluster lid A.
13. Remove combination meter. Refer to COMBINATION METER procedure.
14. Disengage pawls and remove fuse block lid.
Broken square indicates Metal clip
Broken circle indicates Pawl
15. Remove instrument lower finisher.
a. Remove the instrument lower finisher screws.
b. Pull backward while disengaging the instrument lower finisher metal clips and pawl.
c. Disconnect harness connector, and then remove instrument lower finisher.
16. Remove glove box. Refer to GLOVE BOX ASSEMBLY procedure.
Broken square indicates Metal clip
Broken circle indicates Pawl
17. Remove side ventilator assembly (RH).
a. Insert a suitable tool into the top gap of the side ventilator assembly, then starting from center console side, disengage the clips and pawl of instrument panel pad.
Broken circle indicates Pawl
b. Reach through the glove box compartment by hand to the backside of the side ventilator and push against (A) as shown to engage the pawl.
c. Insert a suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask and push against (B) as shown to disengage the pawl.
Broken circle indicates Pawl
d. Lift the side ventilator assembly up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator assembly.
18. Remove front passenger air bag module. Front Passenger Air Bag Module.
Broken circle indicates Pawl
19. Remove instrument upper mask.
a. Insert a suitable tool into backside space of instrument upper mask.
b. Disconnect harness connector, and then remove instrument upper mask.
Broken circle indicates Pawl
Broken triangle indicates Clip
20. Remove instrument finisher D.
a. Insert a suitable tool into upper space of instrument finisher D.
b. Disengage clips and pawls, then remove instrument finisher D.
21. Remove controller. Removal And Installation.
Broken square indicates Metal clip
22. Remove instrument upper panel assembly.
a. Remove bolts and screws.
b. Pull backward and remove instrument upper panel assembly.
23. Remove lighting & turn signal switch. Service and Repair.
24. Remove wiper & washer switch. Service and Repair.
25. Remove hood opener handle and fuel filler lid opener handle. Service and Repair.
26. Remove screws, and then remove instrument panel & pad from passenger door opening portion.
Installation
Installation is in the reverse order of removal.
CLUSTER LID A
Removal
Broken square indicates Metal clip
Broken circle indicates Pawl
1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
2. Remove front pillar garnish. Component.
Broken circle indicates Pawl
3. Remove the instrument side panel (LH/RH).
a. Pull up instrument side panel and disengage pawls.
b. Remove instrument side panel.
Broken circle indicates Pawl
4. Remove instrument side mask (LH).
a. Insert a suitable tool into upper space of instrument side mask.
b. Disengage pawls, and then remove instrument side mask.
Broken square indicates Metal clip
5. Remove instrument side finisher.
a. Insert a suitable tool into space of instrument side finisher.
b. Disengage instrument side finisher metal clips, and then remove instrument side finisher.
Broken circle indicates Pawl
6. Remove side ventilator assembly (LH).
a. Insert a suitable tool into the bottom gap of side ventilator assembly and push against (A) and (B) as shown to disengage the pawls.
Broken circle indicates Pawl
b. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator.
7. Remove the steering column cover screws, then disengage pawls and remove the steering column upper cover.
8. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.
Broken square indicates Metal clip
Broken triangle indicates Clip
b. Lift the instrument upper panel up, disengage metal clips.
c. Pull backward and disengage clips.
d. Remove cluster lid A.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C
Removal
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
Broken square indicates Metal clip
Broken circle indicates Pawl
2. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
Broken square indicates Metal clip
Broken circle indicates Pawl
3. Remove cluster lid C.
a. Remove the upper screws from cluster lid C.
b. Pull cluster lid C backward while disengaging the metal clips and pawl.
c. Disconnect harness connector, and then remove cluster lid C.
Installation
Installation is in the reverse order of removal.
COMBINATION METER
Removal
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes.
Broken square indicates Metal clip
Broken circle indicates Pawl
2. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.
3. Remove front pillar garnish. Component.
Broken circle indicates Pawl
4. Remove the instrument side panel (LH).
a. Pull up instrument side panel and disengage pawls.
b. Remove instrument side panel.
Broken circle indicates Pawl
5. Remove instrument side mask (LH/RH).
a. Insert a suitable tool into upper space of instrument side mask.
b. Disengage pawls, and then remove instrument side mask.
Broken square indicates Metal clip
6. Remove instrument side finisher.
a. Insert a suitable tool into space of instrument side finisher.
b. Disengage instrument side finisher metal clips, and then remove instrument side finisher.
Broken circle indicates Pawl
7. Remove side ventilator assembly (LH).
a. Insert a suitable tool into the bottom gap of side ventilator assembly and push against (A) and (B) as shown to disengage the pawls.
Broken circle indicates Pawl
b. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator.
8. Remove the steering column cover screws, then disengage pawls and remove the steering column upper cover.
9. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.
Broken square indicates Metal clip
Broken triangle indicates Clip
b. Lift the instrument upper panel up, disengage metal clips.
c. Pull backward and disengage clips.
d. Remove cluster lid A.
10. Remove screw (A) and disengage metal clips (B), and pull combination meter out.
11. Disconnect combination meter connectors and remove combination meter.
Installation
Installation is in the reverse order of removal.
GLOVE BOX ASSEMBLY
Removal
Broken circle indicates Pawl
1. Remove glove box screws.
NOTE:
There are three lower and four upper screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Remove glove box assembly.
Installation
Installation is in the reverse order of removal.
INSTRUMENT LOWER FINISHER
Removal
1. Disengage pawls and remove fuse block lid.
Broken square indicates Metal clip
Broken circle indicates Pawl
2. Remove instrument lower finisher.
a. Remove the instrument lower finisher screws.
b. Pull backward while disengaging the instrument lower finisher metal clips and pawl.
c. Disconnect harness connector, and then remove instrument lower finisher.
Installation
Installation is in the reverse order of removal.
CENTER CONSOLE ASSEMBLY
Removal
Broken square indicates Metal clip
1. Insert a suitable tool into front side space of console mask, and disengage metal clips.
2. Disconnect harness connector, and then remove console mask.
Broken square indicates Metal clip
3. On models with A/T or CVT, remove the A/T or CVT console finisher.
a. Place the shift selector in "D" position.
b. Remove shift selector handle. A/T Shift Selector Removal And Installation (A/T) or Removal And Installation (CVT).
c. Pull up and disengage A/T or CVT console finisher metal clips.
d. Remove A/T or CVT console finisher.
5. On models with M/T, remove the M/T console boot.
a. Remove M/T shift selector handle. RS6F94R b. Pull up and disengage M/T console boot metal clips.
c. Remove M/T console boot.
6. Disengage console rear finisher metal clips and pawl.
NOTE:
Broken square indicates Metal clip
Broken circle indicates Pawl
Console rear finisher with armrest is shown in illustration, without armrest is similar.
7. Remove console rear finisher.
Broken square indicates Metal clip
Broken circle indicates Pawl
8. On models with an armrest, disengage console mask cover metal clips and pawls, and then remove console mask cover.
Broken square indicates Metal clip
Broken circle indicates Pawl
9. On models without an armrest, disengage rear cup holder metal clips and pawls and then remove the rear cup holder.
10. Remove console body assembly screws and nut.
11. Disconnect harness connector, and then remove console body assembly.
Broken square indicates Metal clip
12. Remove both of the instrument lower cover LH and RH clips.
13. Disengage instrument lower cover LH and RH metal clips and remove both of the instrument lower covers.
14. Remove screws and then remove center console.
Installation
Installation is in the reverse order of removal.