Operation CHARM: Car repair manuals for everyone.
Home >> Toyota >> 2011 >> Venza FWD L4-2.7L (1AR-FE) >> Repair and Diagnosis >> Engine, Cooling and Exhaust >> Engine >> Service and Repair >> Removal and Replacement >> Engine Assembly >> Installation

Installation





1AR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: INSTALLATION

1. INSTALL ENGINE HANGERS Removal

2. REMOVE ENGINE STAND

(a) Remove the engine stand.

3. INSTALL ENGINE WIRE

(a) Install the engine wire.

4. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY Installation

5. INSTALL REAR ENGINE MOUNTING BRACKET (for AWD)

(a) Install the rear engine mounting bracket with the 3 bolts.





Torque : 64 Nm (650 kgf-cm, 47 ft-lbf)

6. INSTALL DRIVE SHAFT BEARING BRACKET (for 2WD)

(a) Install the drive shaft bearing bracket with the 3 bolts.





Torque : 64 Nm (649 kgf-cm, 47 ft-lbf)

7. INSTALL ENGINE MOUNTING BRACKET RH

(a) Install the engine mounting bracket RH with the 3 bolts.





Torque : 54 Nm (551 kgf-cm, 40 ft-lbf)

8. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD) Installation

9. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for AWD)

10. INSTALL TRANSFER STIFFENER PLATE RH (for AWD)

(a) Temporarily install the transfer stiffener plate RH.





(b) Tighten the transfer stiffener plate RH with the 4 bolts to the transfer and rear engine mounting bracket.

Bolt A - Torque : 34 Nm (347 kgf-cm, 25 ft-lbf)

Bolt B - Torque : 78 Nm (795 kgf-cm, 58 ft-lbf)

11. TEMPORARILY TIGHTEN FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

(a) Temporarily install the front engine mounting insulator assembly with the 3 nuts.





HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

12. TEMPORARILY TIGHTEN ENGINE MOUNTING INSULATOR LH

(a) Temporarily install the engine mounting insulator LH with the 3 nuts.





HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

13. TEMPORARILY TIGHTEN ENGINE MOUNTING INSULATOR RH

(a) Temporarily install the engine mounting insulator RH with the 3 nuts.





HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

14. TEMPORARILY TIGHTEN REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for AWD)

(a) Temporarily install the rear engine mounting insulator with the 2 nuts.





HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

15. INSTALL FRONT FRAME ASSEMBLY

(a) Set the engine assembly with transaxle to the front frame assembly.

(b) Install the engine mounting insulators RH and LH with the 2 nuts.





Torque : 95 Nm (968 kgf-cm, 70 ft-lbf)

(c) Install the front engine mounting insulator with the bolt.





Torque : 87 Nm (887 kgf-cm, 64 ft-lbf)

(d) Connect the 2 clamps with the engine wire.





16. INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for AWD)

(a) Install the rear engine mounting insulator assembly with the 2 bolts to the engine mounting bracket.





Torque : 75 Nm (764 kgf-cm, 55 ft-lbf)

17. FULLY TIGHTEN FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

(a) Fully tighten the front engine mounting insulator with the 3 nuts.





Torque : 52 Nm (530 kgf-cm, 38 ft-lbf)

(b) Install the hole plug.

HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

18. FULLY TIGHTEN ENGINE MOUNTING INSULATOR LH

(a) Fully tighten the engine mounting insulator LH with the 3 nuts.





Torque : 87 Nm (887 kgf-cm, 64 ft-lbf)

(b) Install the 2 hole plugs.

HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

19. FULLY TIGHTEN ENGINE MOUNTING INSULATOR RH

(a) Fully tighten the engine mounting insulator RH with the 3 nuts.





Torque : 87 Nm (887 kgf-cm, 64 ft-lbf)

(b) Install the 2 hole plugs.

HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

20. FULLY TIGHTEN REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for AWD)

(a) Fully tighten the rear engine mounting insulator with the 2 nuts.





Torque : 52 Nm (530 kgf-cm, 38 ft-lbf)

(b) Install the 2 hole plugs.

HINT
Perform this procedure only when replacement of the engine mounting insulator is necessary.

21. INSTALL STEERING LINK ASSEMBLY (for AWD) Installation

22. INSTALL FRONT STABILIZER BAR (for AWD) Installation

23. INSTALL NO. 1 FRONT STABILIZER BRACKET LH (for AWD) Installation

24. INSTALL NO. 1 FRONT STABILIZER BRACKET RH (for AWD)

HINT
Use the same procedure described for the LH side.

25. INSTALL STARTER ASSEMBLY Installation

26. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY Installation

27. INSTALL GENERATOR ASSEMBLY Installation

28. INSTALL V-RIBBED BELT Installation

29. REMOVE ENGINE HANGERS Removal

30. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

(a) Set the engine assembly with transaxle on the engine lifter.

(b) Install the engine assembly to the vehicle.

(c) Install the frame side rail plates RH and LH with the 4 bolts and 2 nuts.

A - Torque : 85 Nm (866 kgf-cm, 62 ft-lbf)

B - Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)





(d) Install the front suspension member rear braces RH and LH with the 4 bolts and 2 nuts.

C - Torque : 85 Nm (866 kgf-cm, 62 ft-lbf)

D - Torque : 32 Nm (326 kgf-cm, 24 ft-lbf)

31. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

(a) Using SST, hold the crankshaft pulley.





SST : 09213-54015

SST : 91551-80650

SST : 09330-00021

(b) Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter setting bolts.





Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

(c) Install the 6 drive plate and torque converter clutch setting bolts.





Torque : 41 Nm (418 kgf-cm, 30 ft-lbf)

NOTICE:
Install the black colored bolt first, and then the 5 silver colored bolts.

32. INSTALL FLYWHEEL HOUSING UNDER COVER

(a) Install the flywheel housing under cover.





33. INSTALL FRONT FLOOR BRACE

(a) Install the front floor brace with the 4 nuts.





Torque : 11 Nm (112 kgf-cm, 8 ft-lbf)

34. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side) Reassembly

35. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH Installation

36. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD) Installation

37. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for AWD) Installation

38. INSTALL FRONT AXLE ASSEMBLY LH Installation

39. INSTALL FRONT AXLE ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

40. INSTALL FRONT LOWER SUSPENSION ARM LH Installation

41. INSTALL FRONT LOWER SUSPENSION ARM RH

HINT
Use the same procedure described for the LH side.

42. INSTALL FRONT STABILIZER LINK ASSEMBLY LH Installation

43. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

44. INSTALL TIE ROD ASSEMBLY LH Installation

45. INSTALL TIE ROD ASSEMBLY RH

HINT
Use the same procedure described for the LH side.

46. INSTALL FRONT SPEED SENSOR LH Installation

47. INSTALL FRONT SPEED SENSOR RH

HINT
Use the same procedure described for the LH side.

48. INSTALL FRONT AXLE SHAFT NUT LH Installation

49. INSTALL FRONT AXLE SHAFT NUT RH

HINT
Use the same procedure described for the LH side.

50. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY Installation

51. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY Installation

52. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY Installation

53. INSTALL CENTER EXHAUST PIPE ASSEMBLY (for AWD) Installation

54. INSTALL TAIL EXHAUST PIPE ASSEMBLY (for AWD) Installation

55. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

56. CONNECT COOLER REFRIGERANT DISCHARGE HOSE Installation

57. CONNECT SUCTION HOSE SUB-ASSEMBLY Installation

58. CONNECT UNION TO CHECK VALVE HOSE

(a) Using pliers, grip the claws of the clip and slide the clip to connect the union to check valve hose to the intake air surge tank assembly.





59. INSTALL ENGINE MOVING CONTROL ROD

(a) Temporarily install the engine moving control rod with the 4 bolts.





(b) Temporarily install the No. 2 engine mounting stay with the 2 bolts





(c) Tighten the 6 bolts.

Torque : 38 Nm (387 kgf-cm, 28 ft-lbf)

60. CONNECT ENGINE WIRE

(a) Connect the connector to the ECM with the lock lever.





(b) Connect the engine wire with the 2 clamps.

(c) Install the ground cable with the bolt.





Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)

(d) Install the ground cable with the 2 bolts.





Bolt A - Torque : 8.0 Nm (82 kgf-cm, 71 in-lbf)

Bolt B - Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)

(e) Connect the ground cable clamp.

(f) Connect the positive (+) cable with the nut and 2 clamps.





Torque : 9.8 Nm (100 kgf-cm, 87 in-lbf)

(g) Install the ground cable with the bolt.





Torque : 8.4 Nm (86 kgf-cm, 74 in-lbf)

(h) Connect the 2 engine wire clamps.

(i) Connect the engine wire to the engine room relay block. Then, install it with the nut and 2 connectors.





Torque : 8.0 Nm (85 kgf-cm, 74 in-lbf)

(j) Install the No. 1 relay block cover.

61. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

(a) Connect the transmission control cable assembly to the control shaft lever with a new clip and the nut.





Torque : 13 Nm (130 kgf-cm, 9 ft-lbf)

NOTICE:
Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in N.

62. CONNECT OUTLET NO. 1 OIL COOLER HOSE

(a) Connect the outlet No. 1 oil cooler hose.





63. CONNECT INLET NO. 1 OIL COOLER HOSE

(a) Connect the inlet No. 1 oil cooler hose.





64. CONNECT FUEL TUBE SUB-ASSEMBLY

(a) Push in the fuel tube connector to the fuel pipe until the fuel tube makes a "click" sound.





NOTICE:
* Check for damage or dirt and foreign objects on the connecting part of the pipe.
* Check if the pipe and the connector are securely connected by trying to pull them apart.

(b) Install the No. 1 fuel pipe clamp.





65. CONNECT OUTLET HEATER WATER HOSE

(a) Connect the outlet heater water hose.





66. CONNECT INLET HEATER WATER HOSE

(a) Connect the inlet heater water hose.





67. CONNECT NO. 1 RADIATOR HOSE

(a) Connect the No. 1 radiator hose.





(b) Connect the wire harness clamp.

68. CONNECT NO. 2 RADIATOR HOSE

(a) Connect the No. 2 radiator outlet hose.





69. INSTALL AIR CLEANER BRACKET

(a) Install the air cleaner bracket with the 2 bolts.





Torque : 7.8 Nm (80 kgf-cm, 69 in-lbf)

70. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

(a) Install the air cleaner case sub-assembly with the 3 bolts.





Torque : 5.0 Nm (51 kgf-cm, 44 in-lbf)

(b) connect the wire harness clamp.

71. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

(a) Install the air cleaner filter element sub-assembly.

72. INSTALL AIR CLEANER CAP SUB-ASSEMBLY Installation

73. INSTALL INLET AIR CLEANER ASSEMBLY

(a) Install the inlet air cleaner assembly with the 2 bolts.





Torque : 5.0 Nm (51 kgf-cm, 44 in-lbf)

74. INSTALL BATTERY

(a) Install the battery tray and battery.

(b) Install the battery clamp with the bolt and nut.





Bolt A - Torque : 9.0 Nm (92 kgf-cm, 80 in-lbf)

Nut B - Torque : 3.5 Nm (36 kgf-cm, 31 in-lbf)

(c) Install the positive (+) battery terminal with the nut.

Torque : 6.4 Nm (65 kgf-cm, 57 in-lbf)

75. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY Installation

76. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY Installation

77. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY Installation

78. INSTALL FRONT FENDER TO COWL SIDE SEAL LH Installation

79. INSTALL FRONT FENDER TO COWL SIDE SEAL RH Installation

80. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH Installation

81. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH Installation

82. INSTALL FRONT WIPER ARM HEAD CAP Installation

83. INSTALL FRONT WHEELS

Torque : 103 Nm (1050 kgf-cm, 76 ft-lbf)

84. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

85. ADD ENGINE OIL Replacement

86. ADD ENGINE COOLANT Service and Repair

87. ADD AUTOMATIC TRANSAXLE FLUID (for 2WD) Replacement

88. ADD AUTOMATIC TRANSAXLE FLUID (for AWD)

89. ADD TRANSFER OIL

90. CHARGE REFRIGERANT Service and Repair

91. INSPECT FOR FUEL LEAK Fuel System

92. INSPECT FOR OIL LEAK

93. INSPECT FOR COOLANT LEAK Testing and Inspection

94. INSPECT FOR EXHAUST GAS LEAK

95. INSPECT FOR REFRIGERANT LEAK Service and Repair

96. INSPECT AND ADJUST SHIFT LEVER POSITION

HINT
Adjustments.

97. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

HINT
Installation.

98. INSPECT IGNITION TIMING Engine

99. INSPECT ENGINE IDLE SPEED Engine

100. INSPECT CO/HC Engine

101. INSTALL FRONT FENDER APRON SEAL LH

(a) Install the front fender apron seal LH with the 2 bolts and clip.





102. INSTALL FRONT FENDER APRON SEAL RH

(a) Install the front fender apron seal RH with the 2 bolts and clip.





103. INSTALL FRONT FENDER LINER LH

104. INSTALL FRONT FENDER LINER RH

105. INSTALL NO. 2 ENGINE UNDER COVER

106. INSTALL NO. 1 ENGINE UNDER COVER

107. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

(a) Fit the 3 retainers and install the No. 1 engine cover sub-assembly.





108. INSTALL COOL AIR INTAKE DUCT SEAL

(a) Install the cool air intake duct seal with the 12 clips.





109. CHECK SPEED SENSOR SIGNAL

HINT
Test Mode Procedure.

pro multis · About Operation CHARM